Question about Hayward SP3015X20AZ 2 HP SUPER PUMP II SP3015X20AZ

1 Answer

Pump difficult to prime-surges-will not pick-up??

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hayward Master
  • 1,389 Answers

Let the air out of the filter as you try to start, this makes it hard for the pump to pick up the water. i would check the impeller and shaft seal,and basket for cracks, if the basket is cracked 99% of the time the impeller is plugged ..shaft seal there is is one one ebay with how 2 for around 10 bucks SMART ! PRIME the pump after a repair !!

Posted on Jun 07, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Prime oil pump, 231 engine


You don't give the year and model, and I'm sure its not a Cutlass Ciera if it has a 231.
Usually its a good idea to pack the gears with grease or vaseline to help prime the pump. Since the pump is mounted on the outside of the engine it can be very difficult to get oil from the sump into the pump gears for the first time.

Jan 30, 2013 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

Pool won't hold prime. I cleaned the filter & basket. Prime is slow to come up but then surges up and immediately drops back down.


check top seal make sure its not damaged if ok check to see if intake union is tight if still bad check impeller for debris

Sep 06, 2012 | Pentair 1.0 Hp Whisperflo Pump

1 Answer

My new Optiflow pump surges..............it seems to not be pulling the water thru the sand filter and discharging as it should. Sand filter gauge fluxuates between 0 and 3 lbs of pressure.


it sounds like you may have a suction side leak on the pump. check the lid o-ring and the suction side fittings to see if there may be a possibility of air being sucked into the pump and causing it to act like it's picking up prime and then losing it.

Jul 25, 2011 | Pentair OptiFlo Aboveground Pool Pump 1 HP...

1 Answer

We have a flotec well pump, less than a year old. The pump is working fine, and is primed. The switch doesn't appear to be working. Is this a difficult item to replace? Home Depot sells the pump and...


To replace the switch, shut off power, remove wires noting all wire locations.
You may have to relieve pressure in the system by using water until the surge tank is empty.
I'm not sure about that.
You do have to either remove the switch from the piping by unscrewing it or remove the piping from the switch by removing the connector and unscrewing the connector from the switch.
Assembly is the reverse. You should use teflon tape of dope on the screw connection below the switch.
The procedure should take about a half hour but you won't have any water during this time.
Gary

Jul 21, 2011 | Flotec TC2151 P2 Well Pump Pressure Switch

1 Answer

My intex pool pump is surging and won't stay primed???


i think its pump side first as its easier to push water through a filter rarther than trying to **** it , Also the only reason it could loose its prime is through air getting in the system.

Jun 06, 2009 | Intex Automatic Salt Water System for ...

2 Answers

How do I prime the STA-RITE DS3HF-01?


I have a sta-rite mkse-6 pump and it has lost its prime..... how do I prime it???

Feb 15, 2009 | Sta Rite Ds3hf 1.50 Hp Self Priming...

1 Answer

Car won't start


It is self Priming. If it will not Pick up, You probably need to Replace the Fuel Pump.

Jan 24, 2009 | 2003 Volkswagen Jetta TDI

3 Answers

How to prime my Pool?


Prime is the term we use to state that the air has been mostly purged from the pump and the pump is moving water. When you have lost the prime, your pump is no longer pumping water through it. Sometimes it can be very difficult to regain the prime on the pump. This will tell you how to get the prime back in these difficult situations

Aug 27, 2008 | Intex 2500 Gallon Sand N Sun Pool...

Not finding what you are looking for?
Hayward SP3015X20AZ 2 HP SUPER PUMP II  SP3015X20AZ Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hayward Pool & Spa Experts

Bill Jordan

Level 2 Expert

373 Answers

john h

Level 3 Expert

22408 Answers

US Parts Center
US Parts Center

Level 3 Expert

719 Answers

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...