Cartridges are not being read - LeapFrog Leapster 2 Learning System

HP Printer does not recognize new cartridges due to cartridge problems, cartridges missing or damaged, and a not compatible cartridge with the printer. Now we discuss each step by step how to fix these errors. ·Make sure installed ink cartridges are compatible with your printer ·Open the ink cartridge access door and remove the ink cartridge from the printer ·Clean the removed ink cartridge with a lint-free cloth. Read more steps to fix HP printer ink cartridge error.

You replaced the "ink cartridges". It needs a "Maintenance cartridge". This is a separate cart, that holds waste ink.

The Canon printer may only use genuine ink cartridges which contain a chip so that you cannot fill the cartridge with ink or use non genuine ink cartridges.

It sounds like you the chip on the black cartridge has been damaged and the cartridge needs to be replaced. When you refill in cartridges you have to be very careful to avoid touching the chip or the nozzle. Replace the damaged black cartridge. Sorry for the bad news.

Welcome to Fixya

This means the the printer cannot determine which cartridge is causing the error. Make sure that you are using original HP cartridges.

Please see troubleshooting procedure below:

1. Remove the color cartridge from the left stall (which has a blue latch) and refasten the latch. Leave the other cartridge in place.
2. Close the printer, wait 10 to 15 seconds, then look at the LCD display.
   • If the LCD display reads Insert Color Cartridge in Left Stall , the color cartridge may be causing the problem. Follow the steps below:
     1. Clean the color cartridge contacts. Click here to see how.
     2. Reinsert the color cartridge into the carriage and close the blue latch.
     3. Close the printer and wait 10 to 15 seconds.
     4. If the LCD display reads Remove and Check Print Cartridges , replace the color cartridge.
   • If the LCD display reads Remove and Check Print Cartridges , follow the steps below:
     1. Reinsert the color cartridge.
     2. Remove the black or photo cartridge, depending on which one is installed in the right stall. The right stall has the gray latch. Be sure to refasten the latch on the empty stall.
     3. Clean the black or photo cartridge contacts.
     4. Reinsert the black or photo cartridge.
     5. Close the printer and wait 10 to 15 seconds.
     6. If the LCD display reads Remove and Check Print Cartridges , replace the black or photo cartridge.
3. If replacing cartridges fails to correct the problem, click the link at the top of this page to contact HP.

Thank you for using Fixya!

If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Hi, are you using Canon or refilled cartridges? If you are using Canon, there's a problem with the cartridge. If you are using refilled cartridges it's because the cartridge has been used. When you first put a Canon cartridge in, the printer reads the cartridge and knows it's a new one, I'm not sure of the mechanics of it, I don't know if it blows a chip or fuse in the cartridge but it can read a new one. If it's been used, it can't read it so you get the message that it can't read it.
Turn off the staus monitor and the message will go and you can carry on printing, it won't tell you when the cartridges are empty, you'll just notice the print quality going downhill.

It's a bad cartridge.

If you have tried multiple cartridges and it still does not read the cartridges, then it is time to replace the printer.  The 920 is an older printer and has done good to work this long.

The following error message appears on the color graphics display after you insert a cartridge: Remove and Check Print Cartridges . The printer will not print. The message does not specify which cartridge has caused the error. Solution This error message indicates that the printer cannot determine which cartridge is causing the error. Follow the steps below to solve the problem.

1. Remove the color cartridge from the left stall (which has a blue latch) and refasten the latch. Leave the other cartridge in place.
2. Close the printer, wait 10 to 15 seconds, then look at the LCD display.
   • If the LCD display reads Insert Color Cartridge in Left Stall , the color cartridge may be causing the problem. Follow the steps below:
     1. Clean the color cartridge contacts.
     2. Reinsert the color cartridge into the carriage and close the blue latch.
     3. Close the printer and wait 10 to 15 seconds.
     4. If the LCD display reads Remove and Check Print Cartridges , replace the color cartridge.
   OR
   
   • If the LCD display reads Remove and Check Print Cartridges , follow the steps below:
     1. Reinsert the color cartridge.
     2. Remove the black or photo cartridge, depending on which one is installed in the right stall. The right stall has the gray latch. Be sure to refasten the latch on the empty stall.
     3. Clean the black or photo cartridge contacts.
     4. Reinsert the black or photo cartridge.
     5. Close the printer and wait 10 to 15 seconds.
     6. If the LCD display reads Remove and Check Print Cartridges , replace the black or photo cartridge.

1. Remove and then reinsert the cartridge indicated in the error message.
2. If the error is still displayed, clean the contacts.

1. If the error message is Error. Remove and Check Black or Photo Cartridge , the following steps may help:

1. Remove both cartridges, lower the latches, and close the printer access door.
2. Turn off the unit by pressing the On button on the front panel. Wait for the printer to completely shut down.
3. Turn the printer back on by pressing the On button.
4. When the message display reads Insert Print Cartridges , open the access door and replace the cartridges.

1. If neither of the steps above fixed the problem, either the cartridge or the printer is faulty

Hi. This is from Dells site regarding automatic ejection of tape once inserted:

The PowerVault 110T DLT VS160 Tape drive reads and writes DLTtape VS1 cartridges. The PowerVault 110T DLT VS160 Tape drive can read - but not write - DLTtape™ IV cartridges written using the DLT1/VS80 format. NOTE: The PowerVault 110T DLT VS160 Tape drive automatically ejects any other cartridge types and any cartridges whose format it cannot read. Make sure all cartridges that you want to use for writing are DLTtape VS1 cartridges.


Perhaps your cartridge is improperly formatted or is of the incorrect type?