FXD RC Helicopter - helicopter fully charged, new batteries in controler, first time using. 'copter unresponsive, will not do anything but blink lights. Manual says that controller light should go on when powered on, then take throttle full up, then full down, light should go off -- then 'copter will respond. Have done this, lights do respond as described, but copter still sits there, unresponsive.

Search Results

How To Fix Your RC Helicopter - YouTube

? 4:22
https://www.youtube.com/watch?v=R65JJYwSH50
Jun 28, 2010 - Uploaded by R/C 101
Does your RC helicopter spin out of control in the air or ... thing that the video says but there nothing wrong about it the remote is fine but the propeller .... i have a brookstone RC stunt copter that i have not used in a few months. i .... however when I come to fly it, it makes a sound but the wings aren't working.

All comments on How To Fix Your RC Helicopter - YouTube

https://www.youtube.com/all_comments?v=R65JJYwSH50
where can I buy new gears and pinions for my mini rc helicopter?. Read more Show.... The two pins on the charger port aren't working they won't charge ..... The charging light is off meaning the battery is charged. Any ideas? ..... So, the motor spins the correct way but there is no gear to transfer the power to the rotors 'A'.Missing: silver ‎bullet

rc helicopter light flashing Remote Controls Questions

Is the "flight light" blinking on the copter? If you connect the USB cable to the copter will it power up? Have you tried different batteries in the remote? Check the pins in the charging port on the copter, Otherwise there's not a lot that can be done with these little RCs.

Are there electrical contacts on the bottom of the helicopter?
See if there is a place on the remote where you can attach the copter. Use the remotes' batteries to charge the copters' built-in, non removable battery.
Also... Google.

If your Brookstone Stunt Copter RC helicopter is not getting enough power after being charged, there could be a few different issues that could be causing this. Here are a few things you can try:
Make sure the battery is fully charged: It's possible that the battery was not charged for a long enough period of time, so make sure the battery is fully charged before trying to fly the helicopter again.
Check the battery connections: Make sure the battery is properly connected to the helicopter and that the connections are clean and free of corrosion.
Try a different battery: If the issue persists, try using a different battery to see if that resolves the problem.
Check the transmitter: Make sure the transmitter is properly charged and functioning.
Check the helicopter's Motor: Check the helicopter's motor to ensure it is working properly. If the motor is not working, the helicopter will not have enough power to fly.
Check the helicopter's circuit: Check the helicopter's circuit, if any of the circuits is damaged, it may cause the helicopter to lose power.
If none of these steps resolve the issue, it is possible that the helicopter may be defective and require repair or replacement. In that case, contact Brookstone customer support for further assistance.

did you charge the helicopter.... you need to put the charging cable in to the copter. and charge up can use a usb power plug. when charged the light on the usb cable should light up or flash. also if you take the plastic cover off the front there is a battery in there and a board check to see what number its set on. it takes around 5 seconds for the remote to recognise the unit.

I presume you have lights & sound on the controller when you turn it on - fourteen quick beeps and then a different toned fifteenth beep. The screen lights (blue). Insert the battery (lettering facing up toward the helo fuselage unitl it's seated all the way - an LED inside the fuselage, visible from behind, quick flashes and then begins a slower blinking.

Once the helo battery is inserted, turn on the controller, which starts the aforementioned beeping. On the last controller beep the helo's LED will stay lighted, indicating the helo & controller are synched.

I had a problem making sure the battery was inserted all the way into the helicopter. You'll know it's inserted properly when the LED inside the helo flashes.

Hi, My X107 MINI HELICOPTER does not receive transmit anymore. It was working fine before. It only flys if I hold the remote control right next to the sensor. If I move it away it loses transmit. Both units have full power. How do I solve this problem.

Test the batteries somewhere else, the batteries might be bad.
Then test a different set of batteries in the RC.

Check your battery pack to see if the controller lost power or the battery pack in the RC ARF to ensure that, the copter can receive.

Mine's exactly the same as yours. Although the transmitter shows A B C the switch has only two positions, so there's a choice of two only. I doubt it's possible to fly 3 at the same time.