Need to replace the complete sponge and leather cover on our massager, also the suspionage pads. Do you sell these and where are you located in the Portland, Oregon area.

dont know try manufacturer -fixya doesnt sell products

You should just replace the unit. The pads are not available.

most chairs are made out of leather, vinyl, or some kind of synthetic leather. In general, vinyl is the best material because it is the most able to stretch (from the massaging bars pushing on it repetitively) and the best at handling heat (which is included in most massage chairs). Leather will begin to crack after some period of use, because it is not as susceptible to stretching

Warming pads for massage tables are a great idea especially in colder weather so that your clients don't feel any discomfort. They are sold in nearly all places that sell massage tables but check out this Amazon link to get some ideas http://www.amazon.com/Master-Massage-Table-Warmer/dp/B0002ISPPW

Out-of-Warranty Service

Core Products will repair most Jeanie Rub Massagers after the warranty has expired. Some of the very early models can not be repaired but can be returned for a $50.00 credit towards a new unit.

It is difficult to determine the extent of the repair until the unit is inspected however, we guarantee the service call will not exceed $89.00 plus shipping.

1-800-338-7014

Basic Service Package - $49.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad

Complete Service Package - $89.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad
- Replace motor

Cord Replacement - $25.00 + $13.00 Shipping
- Replace worn cord

There is a 90-day warranty on any service that is performed by Core Products International.

Where to send it
Core Products International, Inc.
RETURNS DEPARTMENT
1505 Parker Ave, PO Box 627
Chetek, WI 54728

If you have any questions regarding our service
information please call 800-338-7014.

That motor is located at the base of the backrest unit. It operates a lead screw drive that positions the kneading/tapping motors and rollers. The motor is controlled by the PCB unit that covers the length of the back of the massaging unit. Human Touch will not sell individual replacement parts. They will sell only the entire backrest assembly for $600 plus $60 shipping. It can be replaced without tools in less than five minutes.

Out-of-Warranty Service

Core Products will repair most Jeanie Rub Massagers after the warranty has expired. Some of the very early models can not be repaired but can be returned for a $50.00 credit towards a new unit.

It is difficult to determine the extent of the repair until the unit is inspected however, we guarantee the service call will not exceed $89.00 plus shipping.

1-800-338-7014

Basic Service Package - $49.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad

Complete Service Package - $89.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad
- Replace motor

Cord Replacement - $25.00 + $13.00 Shipping
- Replace worn cord

There is a 90-day warranty on any service that is performed by Core Products International.

Where to send it
Core Products International, Inc.
RETURNS DEPARTMENT
1505 Parker Ave, PO Box 627
Chetek, WI 54728

If you have any questions regarding our service
information please call 800-338-7014.

Hello,to replace it you must take it to cannon service,to clean it you can try Opening your printer,but first wear glove to protect your hands,locate the waste ink pads on the instide of your printer(small partson the right).You can remove the pads and the holder with gentle pull,using a tissue or a sponge soap as much ink you can and clean the area around the waste ink.It should be one more waste holder in the right back bottom of the printer. A kind of sponge. There are few screws and plastic parts to be removed and this sponge needs to be washed, dryed and placed again. Be careful and patient.Take a photograph or note somewhere, so you can trace back your steps.The drive motor on the side (behind the waste ink pads) has to be removed to get to the main sponge. You also need to take care as you lift the slide/carriage.
Carefully replace the holder and the pads and close printer.Whilst printer is disconnected from the mains power, press and hold the power button and reconnect to ac power,release the power button,press the power button again.Your done
Good luck

Hi Beverley

There is some confusion here. You say "ink sponge needs replacing" in an Epson C86 (although you have your query posted under HP Officejet 5610!) - I presume you mean the waste ink pads. If so, you need to dismantle the printer - the pads are not under the print head but deep inside the case. I can provide all the information you need to complete this task if you really want to do it yourself. Please post a new comment requesting this assistance if you do.

Out-of-Warranty Service

Core Products will repair most Jeanie Rub Massagers after the warranty has expired. Some of the very early models can not be repaired but can be returned for a $50.00 credit towards a new unit.

It is difficult to determine the extent of the repair until the unit is inspected however, we guarantee the service call will not exceed $89.00 plus shipping.

1-800-338-7014

Basic Service Package - $49.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad

Complete Service Package - $89.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad
- Replace motor

Cord Replacement - $25.00 + $13.00 Shipping
- Replace worn cord

There is a 90-day warranty on any service that is performed by Core Products International.

Where to send it
Core Products International, Inc.
RETURNS DEPARTMENT
1505 Parker Ave, PO Box 627
Chetek, WI 54728

If you have any questions regarding our service,
please call 1-800-338-7014.