Hello! We have some problem whith 1 chanel, when 2

Hello,

For Solving do the following steps
1. Check the Power cable is inserted properly
2. Check the data cable is connected properly to cpu and printer
3. Re-install the drivers for your appropriate OS

or

1. Click on Printers - > Add New Printers
2. Follow the steps and choose IBM Printer in the left pane and select the printer "IBM Proprinter ii"
3. Finish the Wizard and restart the system

Let me know that i Fixya! the problem

B.K.Acharyulu

Hello

Audio and Video Front Inputs are available

for a quick connection of a VCR, to playback

video from a camera or attach a gaming

device. Use the AV button on the remote control

to tune these inputs.

1 Connect the video (yellow) cable

from the Video output on the Camera

(or accessory device) to the Video (yellow)

Input located on the FRONT of

the TV.

2 For Stereo Devices: Connect the audio

cable (red and white) from the Audio

Left and Right Outputs on the Camera

to a Stereo to Mono adapter. Then plug

the single end of the adapter to the

Audio In (white) jack on the FRONT

of the television.

For Mono Devices: Connect one end

of the audio cable from the Audio Out

jack on the device to the Audio In
(white) jack on the FRONT of the television

3 Turn the TV and the accessory device

ON.

4 Press the AV button on the remote

control to tune the TV to the side input

jacks. "Front" will appear on the TV

screen.

5 Press the PLAY
button on the

accessory device to view playback, or

to access the accessory device (camera,
gaming unit, etc.).

Repeatedly pressing the AV button on the

remote control will toggle the picture source

from the current channel, or Front input

jacks.

Note: The Audio/Video cables needed for

this connection are not supplied with your

TV. Please contact your dealer or Philips at

800-531-0039 for information about purchasing
the needed cables
OK

Are you using a Mixer as a pre-amp for this set-up? For example, I have a Numark CM200 where I have all of the inputs and outputs I need to run. DJ IO is connected to Chanel 1 and Chanel 2 Lines in my mixer. The DJ IO is conected to my computer by USB cable. In Traktor souncard settings chanel 1 is set to (3&4) Chanel 2 (2&1) also, devise set up is Numark DJ IO and in External mode. Of course the mixer is conected to my amp and speakers conected to the amp as well.

1-4-2-5-3-6
Now you need to know which cylinder is which. If you stand at the front of the truck looking at the engine, the number 1 cylinder is on the left closest to you. The left bank has cylinders 1-3-5 and the right bank has 2-4-6. So number 1 is at the left front and number 6 is at the right rear.

What you have to do is replace the o2 sensor on bank 1 sensor 1.This is the front sensor on the left side on the exhaust system.Left side is bank 1 and right side is bank 2.Make sure the connections are good first.Usually it`s the internal heater in the o2 sensor.Hope this helps.Good luck.

need to narrow it down, using 1 turn table ONLY with the mixer on channel 1 (the chanel that is working) to test reciever is working properly and sound working on both side of the speakers, this eliminate the first turn table. Next, disconnect the working turn table (1) and connect your second turn table to the same chanel and see if you getting the sound coming chanel 1 just as your first turn table did. If you getting sound coming out from turn table on ch1 than is not the turn table issue. It will be you mixer having problems. You cant solve the problems having everything connected. Testing one turn table at a time using working chanel on the mixer to see if both turn table working properly. If you use the same chanel testing both turn table and the second one does not work than it will be one of your turn table is faulty. Note: if you find and test both of your turn table is working properly than it will be your mixer. good luck and hope that help..

Hello canelo63,

Your question appears under the product listing for the Dual XPA4100 but the in the text you say the amp is actually a Jensen, so it's not possible to provide specific connection information.

But most bridgeable amps can be connected to a single subwoofer and the other two channels used to drive a set of regular speakers. I'd connect the front speakers to channels 1 and 2 and wire the subwoofer to the bridge connections of channels 3 and 4. On the XPA4100, the bridge terminals are the first (negative) terminal on channel 4 and the last (positive) terminal on channel 3.

Hope this helps.

----------------------
1 I 2 I 3 I 4 I
---------------------- the wiev from woofer
5 I 6 I 7 I 8 I
----------------------

1- Right Chanel (-)
2- Right Chanel (+)
3- Left Chanel (-)
4- Left Chanel (+)
5- NC (not connected)
6- GROUND ( - )
7- POSITIVE ( + )
8- Remote (from HU)

audio connection must have matching in audio level and symetrical.
1-prepare your connection cabels(better to be colour marked at connector(red for right channel- white for left chanel).
2-take pre amp right out to power amlifier right in.
3-take pre amp left out to power amplifier left in.
4-connect amplifier right out to right loudspeaker.
5-connect amplifier left out to left speaker.
6-adjust volume level and enjoyyy.

Inside the amp check copper6 for loose connection