How to change the fuses - Black & Decker Power Inverter PI400AB

What fuse ? Regular mini fuse ? Just pull it out with the fuse puller tool located in the fuse box compartment . Replace with same number fuse . 5,10 , 20 , 25 etc.. what ever it is . How To Safely Change Blown Fuse

Remove the fuse box cover remove old place new fuse of same size. Step by Step:

1. Locate your car's fuse panel.
2. Take off the fuse panel's cover.
3. Locate the blown fuse.
4. Remove the broken fuse.
5. Insert a replacement fuse of the correct amperage-make note of the fuse panel and your owner's manual on this one.
6. You do keep a few extra fuses of various amperage in your glove box.

How to Find and Replace Blown Fuse in Your Car or Truck

Changing Fuse DMV org

How to Change Vehicle Fuses

How to Change Car Fuse in 8 Easy Steps

images for How to change a fuse panel cadillac 2001


More images for How to change a fuse panel cadillac 2001

Cadillac Crisis DIY: Checking Fuses - YouTube

? 6:25
https://www.youtube.com/watch?v=xwJodTmj7Jo
Apr 8, 2009 - Uploaded by bountyCXVII
Just a simple video about how to check, and replace possibly burn out fuses. also it shows where both fuse ...

How to Find and Replace A Blown Fuse in Your Car or ...

? 3:32
https://www.youtube.com/watch?v=faWZmG0fXy8
Jul 1, 2011 - Uploaded by 1A Auto Parts
How to Find and Replace A Blown Fuse in Your Car or Truck ...How To Wire A Fuse Block - Easy - Duration: 10:56. klowny1969 9,283 views.

Cadillac DeVille Questions - do i have any fuse boxes under ...

www.cargurus.com > Questions > Cadillac > DeVille

CarGurusMar 3, 2013 - That's where you will find your rear fuse block. ... The fuse panel is accessible by removing the shroud cover. ... 2001 Cadillac DeVille Base.

How to change fuse on 68 cadillac - CarGurus

How to Change a Vehicle's Fuses - For Dummies

www.dummies.com/how-to/.../how-to-change-a-vehicles-fuses.html
A fuse box located under the hood. ... A fuse box is easy to recognize, and replacing burned-out fuses is a fairly simple matter. ... Before you open or work on a fuse box, be sure that your vehicle's ignition is turned off.

Changing a Fuse ' DMV.org

www.dmv.org/how-to-guides/fuse.php
The Unofficial Guide to the DMVDon't stress out, it's a pretty easy procedure. ... Step-by-Step: How to Change a Fuse... Replace the blown fuse with a new fuse of the same amperage. ... Consider using the fuse for your cigarette lighter, the radio, or the back window heater.

How to Check Fuses (with Pictures) - wikiHow

Fusing Pressure Roller warm-up failure
• The voltage of the Fusing Pressure Roller Thermistor does not increase by five steps within 20 sec. after the predrive of the Fusing Roller has been started during a warm-up cycle. Remedy 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.

Locate the power regualtor board. The fuse must be there.

C0500: Warm-up failure

Step 1
Check:
Fusing Heater Lamp (H1) turns
ON.

Step 2
Check:
Fusing Heater Lamp (H1) is open-circuited.
<Check Procedure>
Check the resistance across both
ends of the Fusing Heater Lamp
(H1).
The Fusing Heater Lamp is open-circuited
if the resistance is infinity.

Result: YES
Action: Change Fusing Heater Lamp (H1).

Step 3
Check: Thermoswitch 1 (TS1) is operational.
<Check Procedure>
Check the resistance across both
ends of the Thermoswitch 1 (TS1).
The Thermoswitch 1 is open-circuited
if the resistance is infinity.

Result: NO
Action: Change Thermoswitch 1 (TS1).

Step 4
Check: Fusing Unit Interlock Switch (S2) is
operational.
<Check Procedure>
Check continuity across terminals
when the Fusing Unit Interlock
Switch (S2) is turned ON.
• Across S2-1A and S2-1B
• Across S2-2A and S2-2B

Result: NO
Action: Change Fusing Unit Interlock
Switch (S2).

Result : YES
Action: Change DC Power Supply (PU1).

Step 5
Check: Thermistor (TH1) is open-circuited.
<Check Procedure>
Check the resistance across CN15-2
and CN15-3 on the Fusing Unit side
with CN15 disconnected.
The Thermistor is open-circuited if
the resistance is infinity.

Result: YES
Action: Change Thermistor (TH1).

Step 6
Check: The following voltages are supplied
from the Master Board (copier: PWBA).
<Check Procedure>
Check voltage across a Master Board
(copier: PWB-A) pin and GND when
the Power Switch is turned ON.
• Voltage across PJ10A-7 and GND
DC24 V when Fusing Heater Lamp
(H1) is OFF
DC0 V when Fusing Heater Lamp
(H1) is ON
• Voltage across PJ10A-10 and
GND
DC24 V when Fusing Heater Lamp
(H1) is OFF
DC0 V when Fusing Heater Lamp
(H1) is ON

Result: NO
Action: Change Master Board (copier:
PWB-A).

Fusing abnormally high temperature detection (heating side)
Check the fusing unit for correct installation
Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary.
Change fusing unit
Change PRCB
Change DCPU

if unsure of location use a test light or volt meter on fuse until you find the ruptured fuse then change it

Fuser Unit not heating up.