Samsung HT-X40 System Logo

Related Topics:

Posted on Jul 08, 2017

Hi, my Samsung HT-X30 home cinema system has an intermittent audio problem. I use it mostly as a radio via my virgin media box with the Samsung input set to "Digital In". However unless I have the volum up high sound only comes out of left speaker and even when volume set at 20+ the sound is intermittent from right speaker. Is this correctable or do I need a new system? It's about 5 years old and was fine when new.

5 Related Answers

A

Anonymous

  • Posted on Aug 11, 2008

SOURCE: samsung ht-z310 home cinema no sound rear speakers

I seen the same thing when I first opened mine except my "center" speaker wan't working. It had to do with the "Mode" it was in. The Mode button at the botoom of the remote changes the speaker configuration.

There is also an option in the setup that allows you to turn on/off speakers for the system, all of mine were either Present or Small which enables them to work.

Ad

Anonymous

  • 1 Answer
  • Posted on Nov 26, 2008

SOURCE: Samsung home cinema system HT-THX25 Multiregion hacks

Turn on the HT with no DVD. Press the following buttons on the remote: ENTER 8, 4, 2, 6, 9 ENTER 
It will turn off. When turned again on it is a region free HT. 

Anonymous

  • 1199 Answers
  • Posted on Dec 14, 2008

SOURCE: ht-x30 samsung cinema system display unknown disc

TThe player does not play this type of dvd disk! only pre-recorded movies and CDs Try hooking Up a player that plays DVD+ and DVD- disks!Hope I was of help!
(please use The ratings to keep this site free!)

ginko

Ginko

  • 19396 Answers
  • Posted on May 04, 2009

SOURCE: SAMSUNG HT-TZ212 home cinema kit comes up with protect

Protect mode will kicking whenever a fault is detected.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.

Anonymous

  • 3 Answers
  • Posted on Dec 27, 2009

SOURCE: how can i listen to my tv through my cinema system

Use a fiber optic cable

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My samsung ht-x30 shuts down after 5 secs and displays protection

Hello
disconnect all the speaker connections, and switch ON the set only, and see whether any protection function energizes or not. If yes, the fault is with the amp itself, and most likely to some damge of components in the output circuit section of the amp. If the amp does not show any protection, when all the speakers are disconnected, make sure that, any one amoung the speakers be the cause of this problem. Connect one after an other and find out which one causes protection circuit to energize. OK.
0helpful
1answer
1helpful
1answer

Samsung z310

You have to press the AUX button and set the HTS unit to D. IN (DIGITAL IN)
AUX 2 only works for the regular red & white audio cables.


Hope this helps!
0helpful
1answer

Samsung HT-A100 Home Cinema system plays cd only with tv on!

Hi,
You need to put away the remote for your TV and use only the remote for your HT system. Your HT remote should work on your TV by default. Your Samsung HT remote should have a TV button and a DVD/Receiver button (or HT button). When using only the TV, press the TV button and then use it for just the TV and when using the HT system, press the DVD/Receiver button and then you can use the HT system.
If for some reason your TV is not set on the Samsung HT remote by default, your HT users manual should have a list of codes that you can use to program your HT remote. Hope that helps you. Gary
0helpful
1answer

Home Cinema Samsung HT Z310R- Speakers not working with TV

Hi,
You need just one cable that goes from your TV to your HT system.
On your TV you should see an RCA jack for "AUDIO OUT" and you need to plug that into your AUXILLARY "AUDIO IN" on your HT system
When you are watching TV and you want the sound to come through the HT system, just set the HT system to "AUX" mode. Most Samsung systems will have 3 'AUX' modes, set the remote on 'AUX 1' then wait a few seconds, if no sound comes through then set it on "AUX 2" wait a few seconds and if it doean't work try AUX 3.
Hope that helps.
Gary
0helpful
1answer

Samsung series 6 tv & Samsung 2:1 home theatre problems

if you got all the lead you should have fibre optics which connects from dvd to tv and then set your dvd to digi in. you should get the sound. i have same cinema system and i have done the same
13helpful
2answers

Samsung home cinema system HT-THX25 Multiregion hacks

Turn on the HT with no DVD. Press the following buttons on the remote: ENTER 8, 4, 2, 6, 9 ENTER 
It will turn off. When turned again on it is a region free HT. 

0helpful
3answers

Not getting sorround sound from my tv

only the hd channels get great surround sound. if your tv has an optical audio out and your surround has the optical in input. then i suggest buying a fiber optic wire for the audio you'll hear a big differance. just hope that the audio stays in sync unlike my cheap *** koss system
Not finding what you are looking for?

275 views

Ask a Question

Usually answered in minutes!

Top Samsung Audio Players & Recorders Experts

Cindy Wells

Level 3 Expert

6688 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Samsung Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...