Wixl123 does not drain after washing ? - Indesit W 123 Front Load Washer

Here are the steps to replace the drain hose on a Kenmore Elite front load washing machine:

1. Unplug the washing machine from the electrical outlet.
2. Turn off the water supply to the washing machine.
3. Pull the washing machine away from the wall to access the back panel.
4. Remove the screws on the back panel with a screwdriver and set the panel aside.
5. Locate the drain hose, which is typically located near the bottom of the washing machine.
6. Carefully remove the clamps that secure the drain hose to the washing machine and the drain.
7. Gently pull the drain hose away from the washing machine and the drain.
8. Take the old drain hose to a hardware or appliance store to find a replacement that matches the length and diameter of the original hose.
9. Connect the new drain hose to the washing machine and the drain using new clamps.
10. Replace the back panel and secure it with the screws.
11. Push the washing machine back into place.
12. Turn on the water supply and plug the washing machine back into the electrical outlet.
13. Test the washing machine to make sure the new drain hose is working properly.

Good Day,
Your washing machine is fully automatic?
the washing cycle is normal?
if yes do the same maybe it will help you.
for the fully automatic washing machine mostly have drain pump, please check the filter of your drain pump, how? remove the cup of your drain pump like a ordinary cup, screw it clock wise or counter clock wise.
Remove drain pump filter and clean it, some hair pins, cotton buds or coins or any small item that coz of clog up.
if your washing machine dont have drain pump ,but fully automatic check the drain motor if running or not? how? open the back cover for top loader washing machine only, select spin cycle and press start to see the drain motor running? the drain motor is like a small box with small wire to pull the lever of the drain to remove water inside, if the motor running or pull the lever of the water pipe but water still inside the washing machine, remove the drain cup or cover and clean it or check if have coin or cloth inside that coz of clog or water stuck,
if the drain pump or drain motor is weak this is will cause and long time draining or totally not running the drain pump or drain motor and its cause of totally stop the cycle of washing machine in rinse time or spin time, because all fully automatic washing machine, after washing cycle the drain pump or drain motor must be on, to remove water before start the next cycle. rinse or spin cycle.

Good Day,
Your washing machine is fully automatic?
the washing cycle is normal?
if yes do the same maybe it will help you.
for the fully automatic washing machine mostly have drain pump, please check the filter of your drain pump, how? remove the cup of your drain pump like a ordinary cup, screw it clock wise or counter clock wise.
Remove drain pump filter and clean it, some hair pins, cotton buds or coins or any small item that coz of clog up.
if your washing machine dont have drain pump ,but fully automatic check the drain motor if running or not? how? open the back cover for top loader washing machine only, select spin cycle and press start to see the drain motor running? the drain motor is like a small box with small wire to pull the lever of the drain to remove water inside, if the motor running or pull the lever of the water pipe but water still inside the washing machine, remove the drain cup or cover and clean it or check if have coin or cloth inside that coz of clog or water stuck,
if the drain pump or drain motor is weak this is will cause and long time draining or totally not running the drain pump or drain motor and its cause of totally stop the cycle of washing machine in rinse time or spin time, because all fully automatic washing machine, after washing cycle the drain pump or drain motor must be on, to remove water before start the next cycle. rinse or spin cycle.

Good Day,
Your washing machine is fully automatic?
the washing cycle is normal?
if yes do the same maybe it will help you.
for the fully automatic washing machine mostly have drain pump, please check the filter of your drain pump, how? remove the cup of your drain pump like a ordinary cup, screw it clock wise or counter clock wise.
Remove drain pump filter and clean it, some hair pins, cotton buds or coins or any small item that coz of clog up.
if your washing machine dont have drain pump ,but fully automatic check the drain motor if running or not? how? open the back cover for top loader washing machine only, select spin cycle and press start to see the drain motor running? the drain motor is like a small box with small wire to pull the lever of the drain to remove water inside, if the motor running or pull the lever of the water pipe but water still inside the washing machine, remove the drain cup or cover and clean it or check if have coin or cloth inside that coz of clog or water stuck,
if the drain pump or drain motor is weak this is will cause and long time draining or totally not running the drain pump or drain motor and its cause of totally stop the cycle of washing machine in rinse time or spin time, because all fully automatic washing machine, after washing cycle the drain pump or drain motor must be on, to remove water before start the next cycle. rinse or spin cycle.

Since I have never physically worked on a Indesit, I can only tell you what a normal washing machince diagnosis would be: Drain pump is not functioning. Possibly something clogging the intake (count you socks) or just stopped working.

My supplier does not have Indesit parts so can't give you the part number for the drain pump.

ds nanra, you need to look first at where the power cord enters the washing machine. It then connects to the terminal block on the inside. There is where you need to check for loose/burnt connections. If you have the means (a voltohm meter or continuity tester) you could check the power cord itself for continuity, which would mean that the cord is fine if it has continuity. This is the first place you need to check. Other than a visual check for obvious defects on the power cords connections inside the washer, you would have to test it with a meter for definitive results.
If you have any other questions, dont hesitate. I would be happy to help you out further.
thanks,
mike

If you go to the site below, you will be able to download the user instructions to your printer, or hard drive.

WWW.INDESIT.CO.UK

In the menu on the left side, click on--

Indesit user manuals

then enter your model number in the search box, and down load.the instructions.
Please leave feedback for my solution.
Thankyou.

How to fit Washing Machine Drum Paddle Lifter
For all free video help on appliance Repairs visitour Video Tutorials
Here's our video guide to replacing a washingmachine drum lifter.
A broken agitator paddle can cause your clothesto tear. Don't let this happen when replacing one is relatively simple.


The plastic paddles in the drum on the laterwashing machines often come loose and come off altogether. They can bereplaced. call them lifters. You usuallyinsert a small screwdriver down one of the holes (it's the 3rd one on ) andgently press down while sliding the lifter out.
Washing trainers in a washing machine is reputedto damage the drum lifters and paddles inside the drum, particularly onnon-quality washing machines.
There are few types of drum lifter; drum Paddle lifters

On hotpoint, creda, Ariston ,indersit and someother makes see video
To fit new paddle, make sure the retaining lugis up slightly see video, line up the lugs on the paddle in the slots in thedrum, and push firmly with both hands towards the rear of the drum, you shouldfeel it click into place, make sure you fit it the correct way round and youare fitting the correct paddle lifter for your washing machine.

Huge selections of lifters are available on thewebsite DrumPaddle lifters

if you have two hoses going into it probably not

From what you wrote I can only hint that a fuse within a machine must have played its part for some reason so you better not mess with it. Call a repairman.