The battery was disconected and now when i turn on the radio it says wait 1 hr

THE UNIT TO POWER
Plug AC power cord to the AC wall outlet. Before switching on the unit, make sure that the voltage of your
electricity supply is the same as that indicated on the rating plate.
BATTERY BACKUP
Insert 2 AAA batteries into the battery compartment. Be sure to observe the proper polarity (the "+" and
"-" signs) as indicated inside the battery compartment.
In case of power failure or interrupted AC power, the current time, alarm time settings, and stored radio
stations are preserved in the memory of the unit using the battery back-up function.
SETTING THE CLOCK
1. With the unit in CLOCK mode, press and hold the CLK/MEM button for about 1 second, the time will
begin to flash on the LED display.
2. Press the ?/HR button to adjust the hour.
3. Press the ?/MIN button to adjust the minute.
4. When the correct time is selected, press the CLK/MEM button again to confirm.
SETTING THE ALARMS
1. With the unit in CLOCK mode, press and hold the ALM1/VOL+ or ALM2/VOL? button. The ALARM
time will begin to flash on the LED display.
2. Press the ?/HR button to adjust the alarm hour.
3. Press the ?/MIN button to adjust the alarm minute.
4. When the correct time is selected, press the ALM1/VOL+ or ALM2/VOL? button to confirm.
5. Press the ALM1/VOL+ or ALM2/VOL? button to select the ALARM sound mode - buzzer or currently
set radio station. The alarm buzzer or radio indicator will light up.
SNOOZE FUNCTION
1. Whenever the alarm (radio or buzzer) activates, it can be temporarily suspended for a short period of 9
minutes by pressing the SNOOZE/SLEEP button once.
2. The buzzer or radio will then automatically activate again after the 9 minutes SNOOZE period has
ended.
3. This procedure can be repeated for up to approximately one hour.
DIMMER FUNCTION
Press the DIMMER button to change the brightness of the display.
TURN OFF THE ALARM
When the ALARM activates, press the ALM OFF/SOURCE button to turn off the ALARM.
LISTENING TO THE AM/FM RADIO
1. Press the ALM OFF/SOURCE button to select the FM or AM mode.
2. Press the ?/MIN button or ?/HR button step by step to tune to the desired radio stations.
3. Press and hold the ?/MIN button or ?/HR buttons for approx. 1 second, it will start to search the
next radio station in the direction of the search. The search operation simply finds stations with

Sometimes, the charger will overheat and fail. Try unplugging the charger overnight, plug it back in the next morning, then place the battery in the charger after waiting a few moments. Normally, this will correct the charging discrepancy.

wait 3 hours input correct code or try disconecting battery 1 min then try code

You need to wait 1 hour before attempting to put the code in. Either the ignition needs to stay on 1 hour or drive it for 1 hour. If they key is turned off before then, you will need to start again.

WAIT 1 HR means wrong codes have been entered previously

To restore, leave SWITCHED ON ..UNDISTURBED for as long as it takes to automatically reset itself

In this case it should be 1 hour

Make sure you have the correct code

1.) To begin, if your radio is displays LOC, then proceed to step 2. If your radio says INOP, then turn your ignition to the RUN position, and turn the radio ON. You must leave it like this for a minimum of 1 hour (not 59 minutes) to clear the INOP message. I would wait 1 1/2 hours just in case doing it too early causes the timer to start over.

2.) Turn your ignition to RUN (if not already), and your radio to OFF. Press and hold preset buttons 2 and 3 for around 5-10 seconds to obtain a scrambled version of your radio's original factory set code.

3.) Call a GM dealer with this code. Tell them you are with a local shop i.e. I am Joe with Good Year Highway Tire; Then tell them: We have a 2000 Saturn SL we just changed a battery in and the radio is now locked. My mechanic pulled the pre-code. Could you give me the code? This usally works at no charge.

Once you have the code write it down. Keep atleast 2 copies. Hope this helps!

disconect bettery for 4 hr than try againe

Remove the negative cable from your battery and wait 1 hour the car computer will reset, be carefful that your radio is not anti device, otherwise you would need the code to reset your radio which is a four number code.

Good Luck!

Delete the one you downloaded.
Disconect camera from usb.
Re-Download and wait , after re-boot.
Open easyshare wait. conect camera to usb.
Read again manual and help topics.
Vitally

If it's in safe 2 it's locked. With a battery charger on put the key on handbrake on to take off daytime lights if you have them. Turn the radio on for an 1 hr to 1 hr 1/2 until the display reads 1000. Enter your radio code and your set.