The remoate that came with tv is not turning the unit off or on . we have tried to program a universal remote it the tv will not takr the codes. what are we doing wrong?

The 4-digit code to program a universal remote to work with a RCA LED32B30RQ TV model is likely to be one of the following:
11447 11758 11442
To program the universal remote to work with the RCA LED32B30RQ TV:

1. Turn on the TV
2. Press and hold the "Setup" button on the universal remote until the "TV" button blinks twice.
3. Press the "TV" button on the remote.
4. Enter the 4-digit code for your TV using the number buttons on the remote.
5. Press the "Power" button on the remote. The TV should turn off.
6. Press the "Setup" button again to lock in the code.

If the TV does not turn off after entering the code, please try the other codes listed above. If none of the codes work, you may need to refer to the universal remote manual or contact the manufacturer for further assistance.
Note: The method to program the universal remote may vary depending on the remote brand and model

hi have you tried scanning all codes with the remote untill it picks up the correct signal if you have the manual it will tell you how to do this if its possible it will work after searching the codes.
Also what model remote and what make cable box

Here are some Magnavox universal remote codes you can try to use with your Proscan TV/DVD combo:

• 11963
• 11603
• 12746
• 12260
• 10587
• 12070
• 11990
• 10178
• 10030

To program the Magnavox universal remote to control your Proscan TV/DVD combo, follow these steps:

1. Turn on your TV/DVD combo and point the Magnavox universal remote at it.
2. Press and hold the "Code Search" button on the remote until the LED light on the remote turns on and stays on.
3. Press the "TV" button on the remote to program the remote to control your TV.
4. Enter one of the codes listed above using the number buttons on the remote. The LED light on the remote should turn off if the code is accepted.
5. Test the remote by pressing the "Power" button to turn on the TV/DVD combo. If it works, try other buttons on the remote to control your TV/DVD combo.
6. If the first code you entered doesn't work, repeat steps 2 to 5 with another code until you find the correct one.

If you are still having trouble programming your remote, consult the user manual or contact the manufacturer for assistance.

How To Program A Philips Universal Remote ' Codes For ...

codesforuniversalremotes.com/program-philips-universal-remote/

Here is how to Program any Philips Universal Remote Control. Turn on the device you ... Remote Control Codes December 21, 2015 at 1:19 pm. Stephanie,

Codes For Universal Remotes ' Universal Remote Control ...

codesforuniversalremotes.com/

Universal Remote Control Codes For TV & Audio. ... Codes for Philips Universal Remotes · Sanyo TV Codes for Universal Remotes · Codes for .... I have an 19 inch Emerson flat screen and a RCA universal remote. Please help with the code ..

These are the universal remote codes for Technica TV: 0031 0004 0005 0009 0051 0053 0105 0109 0170 0000 0174 0001 0008 0012 0042 0058

Find codes and methods here.
http://www.docstoc.com/docs/23925020/Programming-Remote-Control-Brand-Codes-TV-Sets

If those codes dont work try the last three(or four) numbers of your TV's serial number.

On my universal remote is just a matter of holding down the TV button till the light stays on, then punching in the three digit TV code. When the TV turns off it's the right code. But read your manual for your controller.

Try 1-800-remotes Factory original.To buy an exact one or very close to the original.

Most universal remotes work the same. Try this.
Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Find the coad at the makers website using the pin number on the back of the remoat or in the battery case

Hold button down for unit you want to program. (TV,DVD,VCR) Then hold down on off button at same time. On/off button will turn off then come back on. When this happens push the play button. Wait 10 seconds and then push again. Repeat until unit turns off. Once unit turns off push rewind button one at a time until unit turns back on then push the stop button.