How do I connect visonic powermax pro to a Redcare secure 2

If the low battery warning keeps reappearing on your Visonic Powermax PIR motion sensor, it is likely that the battery needs to be replaced. Here are the steps you can follow to replace the battery:

1. Remove the battery cover on the back of the sensor by pressing the tab and pulling the cover off.
2. Remove the old battery and dispose of it properly.
3. Insert a fresh CR123A lithium battery into the battery compartment. Make sure to insert the battery with the positive (+) end facing outward.
4. Reattach the battery cover to the sensor.
5. Test the sensor to ensure that it is functioning properly.

If the low battery warning continues to appear even after you have replaced the battery, there may be a problem with the sensor itself. In this case, it is best to contact the manufacturer or a qualified technician for assistance.

It looks like the service timer has been programmed,

Just guessing but the problem when you opened the case to change the battery. That tripped the tamper alarm. On my system it is part of the BIOS and I need to go in to the BIOS to reset it and or turn it off. These links may help:



https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&cad=rja&uact=8&ved=0CDIQFjAD&url=http%3A%2F%2Fwww.visonic.com%2FData%2FUploads%2FPowerMaxPlus_QuickFit_Guide.pdf&ei=e-L0VJPABIPugwTak4HADw&usg=AFQjCNEq2tZrYBaBjnH-v2KoldghnVMeDw

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0CCsQFjAC&url=http%3A%2F%2Fwww.visonic.com%2FData%2FUploads%2FPowerMax_English_User_Guide_DE5450U7.pdf&ei=e-L0VJPABIPugwTak4HADw&usg=AFQjCNF9NNL8dWGK513wC5AnDJU3L0hI0g

0176 Security The system has been tampered with

Usually the green and red, but best way to find out is pop the phone port box where you land line comes into the house, and check to see what wires are used. Some countries use 2 wire systems others use 4

ck to see if the switch area is clean can get dirt in it and make it give a false reading , good luck

Have you tried powering the whole system off and back on?

you can look up site like buy chargers then put your model number in then you will be good to go.

how can i reset poxermax system if i forget master installer code ?

It can be so simple that the charging circuit protects itself by not charging when the cell voltage is so low.
In some cases, you can gently charge the battery with a older type charger, to bring up the voltage so much that the charging circuit accepts the battery and starts its charging.

I found this on the "Home Securty Store" website:

To reset the Visonic Powermax installers code to 9999
The User Code 1 will also be reset to 1111
Unplug the ac transformer and disconnect the main units back up battery then flip it over and find the pins labeled "DEF" on the circuit board. Lower right side of circuit board.
You'll need to short the two pins closest to the bottom of the powermax+ unit labeled DEF,a metal paper clip works just fine.
Have someone plug in the ac transformer while holding the short.Hold this for 10 seconds then unplug the transformer before removing the short.
Remove the short and turn the unit over, plug it back in and try 9999 as the Installer's Code.
(If the reset did not work the first time, try again making sure the short between the def points remains closed during the 10 second power up.)