Question about Durabrand DWT2405 24" TV

1 Answer

The tv does not turn on when I push the power button

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,993 Answers

Hello,

The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.

The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board.

I do not think it needs replacement, rather some defective capacitors are causing this issue.
Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.

The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes)

You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.

What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).

You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors).
After replacing these capacitor(capacitors) most likely the normal operation will be restored.

Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.

If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.

I hope this helps.

Good luck.

Posted on Mar 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I program my RCA universal remote to my element tv , what button to press for the light to blink and the code to put so it can work on my tv


RCA does not have for a code Element TV. With that being said there is a work around:
Turn on your TV.Then push the code search button until the LED still ,when the LED keeps on let go the button now push and release the TV button then push and release the power button until the TV goes off, when the TV turn off stop to push the off button now push the set button the code are already set on the remote control( you might have to push the off button almost 100 times or more until you get the right code for your TV. Best of Luck

Aug 26, 2015 | RCA Televison & Video

1 Answer

Will not turn on?


the lightining battery is not working very well. You should exchange it, so the TV power could get to the Tv and let it Work.

Feb 28, 2008 | RCA F36685 36" TV

1 Answer

Where is the power button of this aquos cardio vision tv? Is there any other way to turn on tv?The power button on remote can't work today.


First thing if there's a TV Button they pushing cause someone might of pushed the SAT or. DVD button. If that don't work check your battery's. some times I tap mine for hand hand lightly and then it works Good luck

Mar 19, 2013 | Televison & Video

1 Answer

How do i program my remote


Hello;

Without knowing the codes for the specific brand names and models of your devices, this is how you program the Zenith MBR3447 for your TV, VCR, DVD Player, CD Player or Audio Receiver:

TV

1. Push the "Power" button on the TV to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "TV" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the TV's IR sensor and push the "Power" button. Pause a second. If the TV fails to shut off, push the "Power" button again. Repeat until the TV does shut off. Each time the "Power" button is pressed the Zenith MBR3447 tries using a different TV device code from its code library to turn the TV off. Therefore, when the TV finally does shut off it's an indication that the remote is temporarily programmed with the correct device code to control the brand of TV you're using.
6. Press "Enter" to save the current code.

VCR

1. Push the "Power" button on the VCR to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "VCR" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the VCR's IR sensor and push the "Power" button. Pause a second. If the VCR fails to shut off, push the "Power" button again. Repeat until the VCR does shut off. Then press "Enter."

DVD Player, CD Player or Audio Receiver

1. Push the "Power" button on the device your programming the remote to control to manually turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "AUX" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the device's IR sensor and push the "Power" button. Pause a second. If the device fails to shut off, push the "Power" button again. Repeat until the device does shut off. Then press "Enter."

Mar 11, 2011 | Zenith MBR3447 Remote Control

1 Answer

Tv wont turn on used it for two months and one day it turns on then the power led light flashes and the opc led light ...


This tv still under warrenty?Yes take ur warrenty repair.This problems very common on Sharp LCD tvs.I have one too.This tv have a Tuner signal board problems.But this tv still use able.Just push power button again after the POWER and OPC flashes.POWER and OPC some will flashes again and wait just push the power button again and wait.Sometimes have to push power buttons and wait power button push out of three or four times power button push POWER and OPC flashes.Than tv will work again.

Jan 06, 2011 | Sharp LC-52D64U 52 in. LCD HDTV

2 Answers

I do not have a manual and need to know how to set it up and the code for a vizio tv.


On your remote you will find a setup botton and what i want you to do is hit set up then hit the tv botton and hit channal up and do that untell it turns off your tv are the channal if that works it tv botton again and your remote will work other wise in the back of your remote it well tell you a code number and go on line to philips and they will give your your codes for you.

Dec 09, 2009 | Philips Magnavox Learning Universal Remote

1 Answer

Model CS- 40307 40 inch Mitsubishi TV will not turn on


continue to push power button until light turns green. verie rate of push and hold

Jul 15, 2009 | Mitsubishi WS-65819 TV

1 Answer

RCA universal 3 digit remote code for diamond vision TV


turn on your tv.Then push the code search button until the led still ,when the led keeps on let go the button now push and release the tv button then push and release the power button until the tv goes off,when the tv turn off stop to push the off button now push the set button the code are already set on the remote control( you might got to push the off button almost 100 times or more until you get the right code for your tv.Good luck

Aug 09, 2008 | Televison & Video

1 Answer

Lost codes


Try this turn on your tv manually,Then on the control remote push and hold the code search button until the indicator light stays lit,release the code search button now push and release the device button TV and next you gotta push and release the power button until the TV turns off ( you might do this per about 150 times be patience) when the tv turns off you push and release the Enter button and the code be saved.
Good luck.

May 10, 2008 | RCA Universal Remote Control

Not finding what you are looking for?
Durabrand DWT2405 24" TV Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Durabrand Televison & Video Experts

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

The Knight
The Knight

Level 3 Expert

76099 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a Durabrand Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...