Skyscan atomic clock weather station. doe not receive signal from outdoor transmitter. For the outdoor transmitter sensor light (red) does not go on. tried to take out and replace batteries and then replaced batteries did not work. also hit re set button on clock did re set but signal still not working. rest of clock works except transmitter. mode is skyscan atomic clock wireless weather station about 3-4 years old.fc equity 81690

It is the transmitter to an atomic clock and temperature display. It is in the window to collect the data from the satellite and pass it to the clock.
SkyScan Atomic Clocks - Customer Support, User Manuals ...https://skyscanatomicclocks.comThe SkyScan® Atomic Clock automatically sets itself to the correct time and date by receiving and decoding the NIST radio signal with an internal receiver. It ensures daily accuracy to the fraction of a second by refreshing the signal each day.‎User Manuals · ‎Daylight Saving Time · ‎Support Desk · ‎Quick Reference Guide for...

Or a Lacrosse Weather Station part

Skyscan – La Crosse Technologyhttps://www.lacrossetechnology.com › pages › skyscan
Ordering Replacement SkyScan Temperature Sensors To order a replacement sensor for your item, please locate your model number in the list below and click ...

SkyScan (tx6u/86722alu) 433mhz Temperature Transmitter ...https://www.ebay.com › ... › Weather Stations
Item description "The La Crosse TX6U works outdoors by sensing temperature and transmitting that information to an indoor station. It can transmit to a base up to 80 feet away. Multiple sensors can be assigned a number so that it will be clear which information from which sensor is displayed."
US$28.66 · ‎In stock

[PDF]WS-8117 ATOMIC CLOCK WITH OUTDOOR WIRELESS ...

https://www.lacrossetechnology.com/products/.../misc/8117-manual.pdf

NOTE: Do not set the clock until the outdoor temperature is displayed. .... The unit will still try and receive the signal every day despite it being manually set. ..... sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes ... Beforesending the atomic clock in for repairs, contact La Crosse Technology.

La Crosse Technology Top Solutions

https://www.lacrossetechnology.com/support/top_solutions.php

A: Complete a restart for display with the temperature/humidity sensor: ... to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing ... Products set outside of these time zones will not search for a WWVB signal as it is ... locate the Clock or Weather Display near an outside wall and point the unit in ...

Common issues weather stations: Click Here

www.weather-station-products.co.uk/faqs/common-issues-weather-stations

Under £30 £30-£75 £75-£125 From £125 Birdhouses/Feeders Outdoor Clocks ... I'mnot getting any outdoor readings from my outdoor sensor, what do I do? This willcure 90% of all sensor connection problems, important you must ... is the airtemperature, to get this reading you need to place the unit away from direct sun.

Replacement Temperature Sensor ' AcuRite

www.acurite.com > All products

Hello

The SkyScan ATOMIC Clock

With the Skyscan Atomic Clock, you have the most accurate timepiece within the continent. It can receive the time signal transmitted by the National Institute of Standards and Technology (NIST), which is regulated by 3 atomic clocks and deviates less than 1 second within 3,000 years. The NIST broadcasts the time signal (WWVB, 60kHz) continuously from Fort Collins, Colorado. This signal can be received anywhere in the continental USA that long wave (AM) radio reception is possible with a portable radio. It is expected that the signal can cover a distance of over 2,000 miles from the transmitter. Therefore, your clock will receive the signal within the broadcast range anywhere an AM signal can be received; generally the signal cannot be picked up in massive metal and concrete structures unless near a window. In addition, some environmental effects (see next page) may affect the transmitting distance.

This clock will set it's self in a 24 hour time frame. You need only set the time zone your in.

If it does not correct it;s self change walls and location in your house.

The transmitter is located in Fort Collins, Colorado. this station transmits the time codes and is best received at night.

Hope this tip helps.

R/
David

The clock will set itself at specific time set times, this is likely to be at 0200 0400 and 0600.
You will however be required to set the time zone, the switch is likely to be on the back.
INFO:
Atomic Time Synchronisation:
How does it work.
SHORT VERSION:
Radio set clocks and watches receive a 60-kilohertz, radio signal from the NIST the official timekeeper for the US and is located in Boulder, Colorado. Ft. Collins. they use atomic clocks and transmits this official time via high frequency short-wave and low frequency AM radio signals, satellite transmission, Internet, and via telephone.
??
REFERANCE LINKS:
OFFICAL TIME:
http://www.time.gov/timezone.cgi?Eastern/d/-5/java
PHOTO OF ANTANA TRANSMITTERS:
http://tf.nist.gov/stations/wwvb.htm

Seems to be a consistent problem with Skyscan. I have the 88800 model and my outdoor transmitter isn't transmitting the temperature either. We've replaced the batteries in both the transmitter and clock and nothing for outdoor temp. It's only been used for 9 months.

Simple, the instructions state that when changing the batteries on the outside temp. sensor, you must also change the batteries on the main clock unit. I had same problem when I changed the sensor batteries until I pulled the batteries from the clock and it reset fine. ( Sensor batteries first, then clock batteries. ) The clock will reset to atomic time overnight so don't worry if it doesn't read correctly at first.

Try changing the batteries in the CLOCK. I had the same problem in a 3M similar clock and it didn't read the transmitter correctly or eventually, at all, when the CLOCK batteries were getting low.

After replacing the transmitter batteries several times, I tried replacing the clock batteries. They must have been getting low. Once I put in new batteries in the clock it worked fine. Good Luck.

You need new SioScan Temperature Transmitter 433 MHz. Take a look on amazon La Crosse Technology TX6U Wireless Temperature Sensor for 433 MHz units.... Hope this was helpful. cheers