Programming my remote to control the sound on my TV

DIRECTV - Support: Your Remote Control

www.directv.com/DTVAPP/equipment/demoInfo.jsp?assetId...

DIRECTVTrying to get your DIRECTV remote control to work with other devices? ... TV Power On & Off - If your receiver turns off while the TV turns on, press TV Power On ...

Program the remote for your TV - Fiber Help

support.google.com > ... > About the remote control

GoogleThe Google Fiber remote control is not designed to fully control external audio equipment. ... Press and hold the button on the original TV remote that you want to program on the Google Fiber remote. If the learning works, the TV power button on the Google Fiber remote blinks twice ...

How to program your DIRECTV remote control:

Press MENU on remote.
Select "Parental, Favs and Setup".
Select "System Setup".
Select "Remote".
Select "Program Remote".

While aiming remote at device, follow onscreen instructions to program remote to TV, DVD, or other device.

How to program the white DIRECTV remote to your TV

Look up the control codes for your DIRECTV remote control.
Make sure your TV is turned on.
Slide the mode switch at top of remote to "TV".
Press and hold the MUTE button. This is located above the number 1 button.
While still holding down MUTE, press and hold the SELECT button until the green light at the top of the remote flashes twice.
Enter the first TV code you have. The green light on remote should flash twice.
Aim remote at TV and press PWR button once. The TV should power off.
Once the TV is able to power off/on and control the volume, slide the mode switch at the top of the remote back to the left (DIRECTV). Your remote is now programmed.

If the TV does not power off, repeat steps 4, 5, 6, and 7, using the next code for your TV brand.

If remote control fails to program using all available codes, try scanning for the code.

How to scan for TV codes on your DIRECTV remote

Make sure your TV is turned on.
Slide the mode switch at top of remote to "TV".
Press and hold the MUTE button. This is located above the number 1 button.
While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.
Then enter 9911, the green light on remote should flash twice.
Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.
When the TV powers off, press and release the SELECT button.

Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

You can find more help in the Remote Controls section of our Technical Forums at forums.directv.com. You can also use our Interactive User Guide to learn the ins and outs of your remote control.

To program your Sony RMT-V306 remote:

1. Set TV_VIDEO switch to TV
2. Turn on television to be programed
3. Press & hold the I/O (Power) button
4. Enter TV code (Toshiba = 07)
5. Release I/O button
6. Press I/O to turn off TV

If you have a different brand TV, you can get the code from Sony's e-support site here.

• Remember, when changing batteries you will need to reprogram remote.
• The RMT-V306 will not control all functions of your component.
• Although not common, there may be some components the RMT-V306 cannot control.

Hi there,

It is possible that you will need to re-program your remote control, it sounds as though the remote has lost it's settings. This can happen when changing batteries, usually a remote will retain the code for around ten minutes or so once the batteries have gone flat or have been removed, after that time it loses it's code. I assume the batteries are new so try re-programing the remote control for your tv with the correct code and hopefully this will work.

Hope this helps,

James

You need to try a different code,505,506,516,523,526,566,573,612,627,647,652,653,654,655,656,658,659,664,665,667,669,670,679,680,704,717,730,738.....hope this was helpful....

I can help you with your Toshiba TV & DirecTV remote control.

To get your TV setup so that you can view your DirecTV on it, I recommend you program your DirecTV remote to control your TV and then use the DirecTV remote to change the input of your TV to view the DirecTV programming.

You can choose between searching for the control code and
entering a code from the Toshiba TV list.

This is a list of all the Toshiba TV control codes for DIrecTV remote controls:

11524, 10154, 10156, 11256,
10060, 12006, 11945, 11936,
11935, 11918, 11704, 11656,
11635, 11369, 11356, 11343,
11325, 11306, 11156, 10845,
10832, 10822, 10650, 10149,
10148, 10036, 11971

I hope that helps.
_________________________________________
DirecTV Remote Control Code List Download
DirecTV Remote Control Manual Download
DirecTV Remote Control Code Entry
DirecTV Remote Control Code Search
DirecTV Remote Control Onscreen Setup

efraintellez,

I have provided a link on how to program the remote to your TV. Normally the TV is programmed to the TV button on the DISH remote, although it will work on the AUX button. The link is:

http://www.dishnetwork.com/SupportSection/remote-setup

The TV setup is towards to bottom of the page. I hope this helps.

Ray Calo
DISH Network

1.Press menu on your remote and then go to settings and press select on setup.

2.Go to remote and then go to reset remote.

3.Press and hold MUTE and SELECT until the light above the mode on tv switch on the remote flashes twice.

4.Enter the code using the numbers on your tv.

5.you have cleared AV1,AV2 and tv modes.Move the switch back to DIRECTV;press select on done.

someone esle found this.. and it worked for me

Program AV1 with 20695, program TV with 10765, then switch to AV1, press select/mute, enter 933, and press select

This will allow volume and mute controls while in DTV mode and allow power on and off while in TV mode. This worked for me on the RC32 remote control.