How to assign IP address through command prompt. Kindly share the screen shot as well ?

Your IP address is a series of numbers that identify your specific computer on the Internet.
If, for some reason, you want to change your IP address, you can do so without going into the command prompt.Click "Start," "Control Panel," "Network and Internet" and "Network and Sharing Center."
Click "Change adapter settings."
Right-click the network you want to change and click "Properties."
Click the "Networking" tab.
Put a check either next to Internet Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4 (TCP/IPv4) and click "Properties."
Click the radio button next to Obtain an IP Address Automatically if you want Windows to assign one, or click "Use the following IP address" to manually change it.
Enter the requested information and click "OK."

Your IP address is a series of numbers that identify your specific computer on the Internet.
If, for some reason, you want to change your IP address, you can do so without going into the command prompt.Click "Start," "Control Panel," "Network and Internet" and "Network and Sharing Center."
Click "Change adapter settings."
Right-click the network you want to change and click "Properties."
Click the "Networking" tab.
Put a check either next to Internet Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4 (TCP/IPv4) and click "Properties."
Click the radio button next to Obtain an IP Address Automatically if you want Windows to assign one, or click "Use the following IP address" to manually change it.
Enter the requested information and click "OK."

There are two ways to find your IP address:
- Through the Network and Sharing Center
- Through the Command Prompt
How to find an IP address through the Network and Sharing Center:
1. From the Start Menu, right-click on Network and click Properties.
2. A Network and Sharing Center window will open. Click View status to the right of Local Area Connection.
3. In the new Local Area Connection Status window that opens, click Details. Your IP Address will be listed among the other connection details.
How to find an IP address through the Command Prompt:
1. From the Start Menu, type Command Prompt in the search field then click Command Prompt once it appears.
GL

Find your computer's IP address : Windows 7, Vista, and XP, using the command prompt

1. Click Start, and then select All Programs. Note: If this doesn't match what you see, refer to About navigation settings in Windows.
   
2. Click Accessories, and then Command Prompt.
   
   
3. At the command prompt, enter: ipconfig The IP address (or IPv4 address, if you are using Windows 7 or Vista) will be a series of numbers following the pattern xxx.xxx.xxx.xxx (i.e., 156.56.27.32).
   

Note: If you are using PPP with a modem at home, your IP address will change each time you log in.
Windows 7, without using the command prompt

1. In the system tray, click the network connection icon and select Open Network and Sharing Center.
   
   
2. To view the IP address of a wired connection, click Local Area Connection. To view the IP address of a wireless adapter, click Wireless Network Connection (Network Name).
   
3. Click Details... . Your IP address will appear next to "IPv4 Address".

Windows Vista, without using the command prompt

1. From the Start menu, right-click Network, and then select Properties. This opens the Network and Sharing Center.
   
   
2. To view the IP address of a wired connection, click View Status to the right of Local Area Connection. To view the IP address of a wireless adapter, click View Status to the right of Wireless Network Connection.
   
3. Click Details... . Look for the address next to "IPv4 IP Address".

Windows XP, without using the command prompt

1. From the Start menu, right-click My Network Places, and then click Properties.
   
   
2. To view the IP address of a wired connection, double-click Local Area Connection. To view the IP address of a wireless adapter, double-click Wireless Network Connection.
   
3. Click the Support tab, and then click Details... . The window that appears will display the IP address.

Your IP address has to be in the 192.168.123.xxx range

The router must be configured to match your

Internet service. If you do not know your

Internet connection configuration, please

contact your Internet Service Provider (ISP).

By default, the router is pre-configured with

these settings:

• Automatically set IP addresses for

computers on your LAN (connected to the

router's ports 1-4). The router acts as a

server for dynamic host configuration

protocol (DHCP) and assigns IP addresses

in the range 192.168.123.100 through

192.168.123.199

• The default LAN IP address for the router is

192.168.123.254 with a subnet mask of

255.255.255.0

• The Internet service connected to the
router's WAN port uses a dynamic IP

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Before you do the steps below make sure your Networking Interface Card (NIC) is working. You can find out this by typing 127.0.0.1 in command prompt (to bring command prompt type cmd in the RUN command)

Step 01: type ncpa.cpl on the Run command
Step 02: Right click the network connection and navigate to the properties.
Step 03: Under Networking Tab select the Internet Protocol IP v 4 click property button right underneath it.
Step 04: Under General make sure to click the Obtain IP automatically and Obtain DNS automatically. This allows your belkin wireless router to assign IP address dynamically.
Step 05: Open your web browser and type 192.168.1.1 (usually this address is your default gateway if not 0.1 or 2.1 on the address) and access the belkin router.
LAN settings: IP address should be your default gateway address and subnet mask will assign automatically if not type 255.255.255.0 on the subnet mask section.
Make sure DHCP (Dynamic Host Config Protocol) is on and assign IP pool from next address to starting address and ending usually 254 or 100)
Start 192.168.2.2 End 192.168.2.100

Lease Make sure DNS are assign automatically.
ignore above steps if they are already assigned.
once you finished reboot your computer (you dont have to do this)
Now open browser enjoy.
If you still dont get internet you must check your cabling with ur router to pc. or different port

Thank you Visit www.somdtech.co.uk

Using arp command (Windows 95/98/NT/2000)
From Windows 95/98 MS-DOS prompt or at Windows NT/2000 command prompt, you can use the arp
command to assign the IP address to the network interface card. It is necessary that TCP/IP is set up
correctly on the computer that will execute the arp command. Perform the following procedure:
1. At Windows 95/98, select [MS-DOS prompt] from the [Start] menu. At Windows NT/2000, select
[Command prompt] from the [Start] menu.
2. Execute the arp command. For example, if the MAC address of the network interface card is
00:11:22:33:44:55 and the IP address to assign is 192.168.0.128, then input as shown below,
and then press [Enter].
(Example: C:\>arp -s 192.168.0.128 00-11-22-33-44-55
3. Execute the ping command for the assigned IP address. In this case no response is returned
from the network interface card.
(Example: C:\>ping 192.168.0.128
4. Turn off the main power supply to the print controller and the main body printer, then turn it
back on.
Chapter 2 Setting Up the Network Interface Card
2-4 Konica Network Interface Card INSTRUCTION MANUAL
A Status Page will be output. Check that the IP address is correctly set in the list. Or, when about 5
minutes have passed after having restarted the print controller and the main body printer using the
ping command, check that the network interface card responds correctly. The ping command is also
executed at Windows 95/98 MS-DOS prompt or Windows NT/2000 Command prompt. The example
of executing the ping command is shown below:
(Example: C:\>ping 192.168.0.128

Try going to start on the computer, then click run, then type cmd, then enter ipconfig/all. if your IP address is 192 dot something then you are assigned a private IP address by DHCP that assigns IP addresses automatically to your computer more than likely and those won't allow you on the internet. If you have a 206 or up number then your good because there for public usage and browsing the internet unlike private IP addresses. if you have a private IP address by the number I said type in command prompt ipconfig/renew and it will request a new IP address from DHCP.
If it don't work click my computer, then right click my network places on the left part of the page and choose properties, then click on your connection and choose repair the connection on the left of the page and that should fix and renew your IP address if DHCP won't issue through command prompt.

see there are two types of connection in your laptop pls see u define on which network choose local lan and assign ip adress and save .