Dehumidifier fails to run a full cycle, the unit is plugged in and fails to run for more than 5 minutes. you can unplug the unit and plug it back in and the same thing happens again. i have tried different settings on the unit but no positive results.

If your Midea Cube 20-Pint Smart WiFi Dehumidifier is stuck on "Water Level 50%" even though the tank has been emptied multiple times, you can try the following steps to reset it:

1. Unplug the dehumidifier from the power source and let it sit for 10-15 minutes.
2. While the dehumidifier is unplugged, remove the water tank and check for any obstructions in the water tank outlet or on the float switch.
3. Clean the water tank with warm water and mild detergent, then dry it thoroughly before replacing it in the dehumidifier.
4. Plug the dehumidifier back in and turn it on. If the water level indicator still shows 50%, try pressing and holding the "Water Level" button for 3-5 seconds to reset the sensor.
5. If the issue persists, try performing a factory reset on the dehumidifier. To do this, press and hold the "Timer" and "Mode" buttons simultaneously for 3-5 seconds until the display panel shows "F". Then, press the "Power" button to turn the dehumidifier off, unplug it from the power source, and wait for 5-10 minutes before plugging it back in and turning it on.

If none of these steps resolve the issue, it may be necessary to contact Midea customer support for further assistance or to have the unit serviced by a professional.

Question edited for clarity and spelling of maker name.
Question moved from Computers and Internet category.

Faulty Sensor

https://www.google.com/search?q=hisense+model+dh7019kig+e9+error+code

..

"For the above error codes, Power the unit off, and then unplug the unit for 15 minutes. Plug in and power on. If the issue persists, please contact customer service."
https://edgestar.zendesk.com/hc/en-us/articles/201000315-My-dehumidifier-is-displaying-an-error-code-What-does-it-mean-

Hi,

Here is a tip that explains what can be happening to make the dehumidifier showthat the bucket is full when it is not.

Dehumidifier Problem It shows Bucket Full

heatman101

Hi,

Here is a tip that explains what can be happening to make the dehumidifier showthat the bucket is full when it is not.

Dehumidifier Problem It shows Bucket Full

heatman101

;';'

][[

First, tunr the unit OFF and unplug it for 10 minutes. Then plug it back in and turn it ON. It will automatically set at 70%. Press the - button and lower the humidity extraction level to 45% in increments of 5%. Once you reach 35% press and the - button one more time. Now the unit is set to run continuously, until the bucket is full and the unit turns OFF automatically or you manually turn the unit OFF. In case you have misplaced the Owner's Manual, I have included a link to it, that you can download and print. http://aic.lgservice.com/gcsc/dwn/main

I hope this helped you and thanks for choosing FixYa..

Laverne, most of the time repairing a 7 year old dehumidifier is as costly (parts - if you can find them & labor) as buying a new one. As far as the problem you're having is concerned, it sounds like one of the sensors has failed. You may try the following, t see if the unit will reset itself.

Turn the Master ON/OFF Switch to OFF. Unplug the unit and leave it unplugged for 12 - 15 minutes. Plug the unit back in, turn On the Master On/OFF Switch and set the controls as you normally would. Hopefully, that 12 - 15 minute timeout, allowed the electronics to reset themselves and the unit will function as it should.

Hope it works for you.

Was the hose attached to the bucket or directly attached to the inside of the humidifier?
If it was to the bucket, the hose may have slightly pulled the bucket out of place, disengaging the safety switch. Unplug the unit and wait 5 minutes. Then plug the unit back in. Turn it to ON and remove the bucket and carefully reinstall it. You should hear a "click" sound when it's properly in place and the unit should start back up,

Hope this helps to solve your problem.

There was a recall on these - it depends on the age.  I bought mine in 2003 or 2004, and they sent a repairman out to replace a circuit board.  Call Maytag to see if yours was in the recall.

the compressor motor is badly damaged...surprised it is turning on at all...the starting winding is bad, the running winding is fine...the motor is ...well done. new dehumidifier cheaper than fix