I have a new invicta watch model number 6089 that I just recived yesterday. I can set the time and date but for some reason I can not set the 3 arm?? I have read the instructions and still it will not move. I know the 3 arm moves because it was on 4 last nite and know it is on 14 so if some one can please give me some info, Thank you

View the instruction manuals - Invicta

invictawatch.com/service/view-the-instruction-manuals

Enter your 4 or 5 digit model number to locate your watch. RECEIVE THE NEWSLETTER SOCIAL MEDIA · Terms & Conditions Customer Service Service ...Missing: 12983 ‎subdial

Setting Time Date Invicta Watch Chronograph - SmartBargains

https://www.smartbargains.com/.../Setting-Invicta-Chronograph.html

Know how to set time, day, and date in the Invicta Watch Chronograph. ... Invicta sells several different kinds of chronograph watches, with the two main ... and the Invicta Big Date and Day chronograph - the subdials that measure seconds and ...Missing: 12983

Invicta Reserve 48mm Octane Swiss Made Quartz ...

this watch has a screw down crown. lift up the protector bar or start to unscrew down until it pops out, then turn slowly and pul gently all way out. set the time . tere is 2 positions there. full out time and inbetwwen them is the date and day settings.when there turn up or down until date chages, if it has day and date , up is day down is date.you have to turn few times for it to move..set the date ,set day before and go around . the 12 see number change to might date, set the correct time am or pm. push the crown in and screw in up til hand tight.

Pull crown to position 1 and change date to yesterdays date , then pull crown to position 2, wind clock untill correct time appears (observe when date switches to observe the clocks am/pm cycle, this is useful to ensure the alarm goes off at the right time of day when set)

Hi Friend,

Please check with the below link,which gives the detailed information about the Invicta Watches.How to set the Date and time in your watch.

http://www.invictawatch.com/support_files/instruction_manual/Manual-HiRes.pdf

If you have any Clarification please write back to us

Regards,
Aysaam

I too was confused at first at setting the second hand after reading the directions. I read your post in searching for a solution, then I figured it out. Check the watch face, the second hand is operating using military time. (24 hr. time) You will see 24 hour time embedded on the face.
For example: if you wanted to set both hands to be at the same time to test this. At say 10 p.m. set the second time hand to 22 for 2200 hrs. (10 p.m.) Let's say you woke up at 7 a.m. The second hand would be at 0700 (Embedded on watch face) then at noon it would say 1200 on the watch face... I now use the normal hands for local time and set the 24 hour hand for my home time.
I hope this helps.

I don't have this model, but normally, invicta dates are set by pulling the crown out half-way and turning counter-clockwise.

The Lupah has a chronograph so dont worry about the sub dials while your setting the time. Pull the crown out to the first position and set the time. For the date pull out to the second position and set the date.

To set the chronograph sweep arm pull the crown out and press and hold down the start button. The sweep arm will move into position. Stop it on the 12:00 or 0 position.

The three buttons are the Chronograph start button (top), Crown (middle), and chronograph reset (bottom).
To set the watch pull the crown out to the first position and turn it until it is on the right time.
To set the date pull the crown out to the second position and rotate until you have the right date.
Be sure that when you set the time that you are in the right AM or PM. DO this by watching when the date turns at the 12:00 position. The date changes at midnight so that would be AM.