Im trying to program my remote so all my compents will work on one remote but dish network doesn't have the code for my polaroid vhs/dvd player. The model no is dvc 2010. If anyone has the code please post it.. Thank you

Hi henry walters,

I know it can be frustrating trying to get the codes to program equipment. You can view the link below to search for any codes you may need for your equipment!

Link: http://www.dishnetwork.com/SupportSection/apps/remotecodes.aspx

Let me know if you have any other questions!

Tommy Faust
DISH Internet Response Team

You may want to search for the code by performing a Power Scan, I will include the steps below. If this doesn't resolve this there is most likely a compatibility issue.
Power Scan:
1.) Press and hold the correct VCR button (about six seconds) until all mode button backlights come on, then release.
2.) Press 500 pound (#)
3.) With the desired equipment on, press and hold the VCR/DVD button until all mode button backlights illuminate (about 3 seconds), then release.
4.) Press and release the Power button.
5.) Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
6.) Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.
To verify the code works try several different functions for that equipment.

Daniel Busa
DISH Network
Customer Service

Hello, I wasn't entirely sure what you're trying to accomplish, but if you try this link the DISH remote should work the DVD and TV set. Hope this helps!!!
http://www.dishnetwork.com/downloads/pdf/user_guides_and_manuals/Remote_Codes_Web_Page.pdf


Daniel Busa
DISH Network Customer Service

Hi there! In order to be able to provide the definite codes that will allow you to program your remote to your Magnavox Blue Ray DVD player, I would need the type of remote that you have- this can be found on the back of your remote, it would be displayed as something along the lines of 3.0, 4.0, 5.0, etc. To obtain a few codes that will likely allow you to successfully program the remote I used 5.0 because it is a common remote that is used with quite a few of our DISH Network receivers. The codes you can try for your DVD player would be, 829 (most successful) if not then please try the following, 685, 533, 554, or 556. After trying those codes if your attempts are still unsuccessful you can also check the manual that came with the DVD player from the manufacturer or just contact us here at DISH Network - although I do know sometimes the remote codes can be located in the manual. Hope the codes help & work for you!

-Kirstie DISH Network

Sorry to hear about the original remote, we would be happy to help with getting your DISH remote programmed to your Curtis DVD player. Here is a list ofcodes that should address your DISH Network remote to your Curtis DVD player: 678, 679, 683, 585, 592, and 594. Start by pressing and holding the DVD/VCR button located on the top of the remote until allthe mode buttons at the top of the remote light up, then release. Use thenumber buttons to enter one of the codes for your Curtis DVD player, thenpress the pound (#) button. If the code entered is valid for the remote, the modelight flashes three times.To check that the code works try several different functions on the remote tomake sure it will properly operate your DVD player. Keep in mind that somecodes may not be compatible with your equipment. If this is the case, pleasetry the other codes listed for that device until you find one that iscompatible with your equipment. We hope this helps and thank you forbeing a valued DISH Network customer!


Phillip Chang
DISH Network Customer Service Representative

I had rca remote that did not recieve ir signals but rf signals instead. Check online with rca or in owners manual for what type of signal factory remote sends. The dvd player I had was 5 dvd and that was the case. Dish might have an option like direct tv where you can program rf signals as well. Call dish network support or look online

Do you have a Sanyo Universal Remote ? If not, you program your dish 500 remote for these.

1000,1001,1002,1003,1004
MAGNAVOX and 0000,0001,0002,0003,0004
0057 PHILIPS and 0005,0006,0007,0008,0009