KX-TG1000N new handset 1

Please use the below link to assist you with handset registration.

http://service.us.panasonic.com/OPERMANPDF/KXTG5621S.PDF#page=35

335 is the magic code when you want to remove a previous handset or base station registration!
Handset:

1 " (middle soft key) i L i #

2 Enter "335".

3 "Cancel Handset" i #

LThe numbers of all handsets

registered to the base unit are

displayed.

4 Select the handset(s) you want to

cancel, by pressing the desired handset

number. i #
5 "Yes" i # i {ih}
Base Station:

A handset can be registered to a maximum

of 4 base units. A handset can cancel a base

unit that it is registered to. This allows the

handset to "forget" the base unit.

1 " (middle soft key) i N i #

2 "Registration" i #

3 Enter "335".

4 "Cancel Base" i #

5 Select the base unit(s) you want to

cancel, by pressing the desired base unit

number. i #
6 "Yes" i # i {ih}

I had this problem, and I fixed it by re-registering the phone to the base. Here are the directions for how to do that from the manual:


----->

Registering a handset to the
base unit
The supplied handset and base unit are
pre-registered. If for some reason the
handset is not registered to the base
unit, re-register the handset.
1 Handset:
{MENU}
2 {V}/{^}: "Initial setting"
{OK}
3 {V}/{^}: "Registration"
{OK}
4 {V}/{^}: "HS registration"
{OK}
5 Base unit:
- KX-TG4011 series:
Press and hold {LOCATOR} for
about 5 seconds. (No registration
tone)
- KX-TG4021/KX-TG4071 series:
Press and hold {LOCATOR} for

about 5 seconds until the
registration tone sounds.
If all registered handsets start
ringing, press the same button to
stop. Then repeat this step.
The next step must be completed
within 90 seconds.
6 Handset:
Press {OK}, then wait until a long
beep sounds.
Note:
While registering, "Base in
registering mode" is displayed on
all registered handsets.
When you purchase an additional
handset, refer to the additional
handset's installation manual for
registration.
<-----

See http://service.us.panasonic.com/OPERMANPDF/KXTG4011-MUL.PDF (page 22)

Hello! Have you re-registered the handsets? If not go to page 39...If you have re-registered the handsets...Pull the batteries for 1 hour...reinstall batteries...allow handsets to set in the cradle for 1 minute then test...

Guru...Saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

This works on MY panasonic; May work on yours too!

Registering a handset
The included handset and base unit are
preregistered. If for some reason the
handset is not registered to the base
unit, register the handset.
1 Handset:
{MENU} i {0}{0}{1}
2 Base unit:
Press and hold {LOCATOR/
INTERCOM} until the IN USE
indicator flashes.
LAfter the IN USE indicator starts
flashing, the rest of the procedure
must be completed within 1
minute.
3 Handset:
Press {OK}, then wait until a beep
sounds.
4 {OFF}
Registering an additional handset
See page 5 for information on the
available model.
Start from step 2.

Panasonic KX-TG1050N Cordless Phone. Base handset (No. 1, KX-TGA100N) does not work, no keypad response or dial tone. Green indicator message light ON (should only work with the TG1000N base unit) all the time till battery runs down. Display shows message ?C533?. Can still send and receive calls on extension phones 2 and 3.

well clea the base, you didnt leave much for us to help you on mate.

STEP1:
On the handset you want to discard go to "SETTINGS HS" -> "REGISTRATION" -> "CANCEL BS"
This will discard the registration of the handset to any base.

STEP2:
Using the handset you want to register go to "SETTINGS HS" -> "REGISTRATION" -> "REGISTER HS"and select the base you want (i.e. BASE 1, BASE 2, ..., BASE n).

NOTE:If you do not get access to the BASE you are looking for (STEP 2) then you have to cancel the registration of the new handset to any base. Therefore, follow STEP1 for this handset as well and then follow STEP 2.

After you finish all the above, hold down the "PAGE" button for about 5 secs.

You are now done!!!

Good luck
Simos

I would suspect that you need to de-register both 3 and 4 at the same time before re-registering them. This probably will not work if the base unit still thinks phone number 2 is out there somewhere. It would need to be de-registered as well for the others to move up a notch. I did read the process for de-registering somewhere on the web, don't remember where, just that it involves removing/installing the battery and punching some buttons.