I have an rf20 universal remote. all components are dialed in and working except for my dish network 722 dual hd dvr receiver. I am following the owners manual instructions and when I enter the codes attributable to dish network receivers (122, 167 or 168) nothing happens.

am_witek,

Our 625 receiver is not an HD model. Our current HD models are ViP 211/211k, 222, 612, 622, 722/722k, 922, and our Hopper receiver.

If you have any other questions, let me know!

Tommy Faust
DISH Social Media Representative

Hi my name is Mike Houston a Social Media Representative at DISH. I see you have a Bose universal remote and you want to program it to your VIP622 DVR. We do not have codes to setup other remotes to our DISH equipment. With our SD/HD receivers they are installed with a DISH universal remote that can control many different components including a Bose system. If you have any further DISH questions please e-mail me at [email protected]

It is possible that those buttons have failed, but a bit more likely the remote lost the codes for the TV itself... since almost everything the remote controls... is on the DVR. I apologize if I am guessing wrong in assuming other "TV" buttons (like INPUT) don't function either.

To re-program your remote to recognize your TV (like when the tech first set up the system) choose from the following receiver types to find the correct remote control TV codes for your Zenith.

Remote TV Codes for 722/622/612/411/222/211 Receivers
Remote TV Codes for 625/522/512/510/508/501 Receivers
Remote TV Codes for 811/381/322/311/301 Receivers

Hi tesmathwi572 my name is Mike Houston of DISH Network andI was going over your post and with our DISH remotes that go with the receiverwill give full functionality to change the channels as well as the DVR andaccess the Menu. Buy getting another remote from a store may not program to thereceiver to change the channels, if I can check your account information suchas account number or phone number so I can see about getting the remote thatgoes with that system. I will leave you my e-mail so you can contact medirectly. [email protected]

Here is what I did for my Bose Solo Tv to work on the Bell 9242 receiver.( see page 17 of Bell 9242 guide) 1. Hold down the aux button until all lights flash. 2. Press 2 to ensure Aux is set to audio. 3.Enter code 761 and press the pound (#) button. Now to have the satellite remote default volume to Bose Solo do the following. 1.Press and hold AUX 2.press # pound 3. Press the + side of volume 4. Press 0 5. Press pound ( AUX button will flash 3 times) 6. Press SAT mode 7. Test the volume on Bose Solo. (see page 22 of Bell 9242 guide)

The Sony RM-YD029 Remote control will work with the Dish Network VIP722 DVR HD Satellite Receiver, but the Dish Network VIP722's Primary remote address must be set to 1.

The procedure below will allow Sony RM-YD029 remote control to operate Dish VIP722.

Using the Dish Network Remote Control -
1. Press menu 2 times to get to system info page
2. In the system info page the primary remote address is in a white box (bubble) followed by a Green TV (1)symbol that says IR and indicates you the channel your remote control one is configured. The Sony RM-YD029 will work when this primary remote address number (in the white box) is set to 1.

If the Primary Remote Address of your VIP722 Remote control 1 is not set to channel 1, here is how to change it:

1. While displaying the system info page, press and hold the SAT button on your dish network remote until all other modes are flashing, about 3 seconds.
2. then press the '1' button on the numeric pad of your dish remote
3. then press the '#' button on the numeric pad of the dish remote
4. then press the 'record' button (red dot button - stores setting)
5. At this point you should see a number 1 in front of the primary remote address on the dish system info page

Ensure you enter the corresponding IR code into your Sony remote control per the instructions in the manual or Sony's web site. My 722 works with Sony IR code - 01775.

If you have a dish network system as listed in post a DVR 625 this is NOT possible, it will only work with VIP series Dish Network recivers. and they must be used on teh same model reciever such as Vip 722, tranfer to EXT HD then Watch on another 722!

Remote manufactures and service providers continuously add support for new TV products. If you have the following Satellite or Cable Systems, try these remote codes for Olevia HDTVs.

Also available is the Olevia Universal Learning Remote RC-LRN that offers component programming of most video hardware including your Cable or Satellite Receivers, VCR's, TiVo’s, DVD, Blu-Ray or even HD- DVD players. The learning remote is available at 866-965-3842
Dish Network Remote Codes 506 or 127

could try Dish Network..Remote Codes 506 or 127
Satellite TV Systems Dish Network Remote Codes 506 or 127
Dish Network Remote Codes 506 or 127

you will have to buy the logtec harmony 520 remote it programs on internet and works great

The only solution you may have is to buy a high end universal remote that will control the Dish receiver as well as your peripherals. Dish also has a new receiver- 222k- that offers learning remotes and expanded product codes to support more tv's.The 222k is a dual tuner two room HD non DVR receiver. I hope this assists you. Thanks for using Fix Ya and let me know if I can further assist you.