When running on our treadmill the belt slips.

Frequently Asked Questions - Reebok - Reebok Fitness

https://www.reebokfitness.com/.../FAQItem_-1_20101_30652_faq-tread

Jump to How can I loosen or tighten the walking belt? - ? Play this video Treadmills have two different styles of walking belt adjustment. To see which type ...

Reebok Edge Treadmill 2.2 - YouTube

? 1:49
https://www.youtube.com/watch?v=fWjbWV8f6wE
Aug 27, 2011 - Uploaded by redgoals
Reebok Edge Treadmill 2.2 ... and I feel when jogging im gonna fall off the end of it - I cant see a man using this at all - maybe just for walking.

running machine belt slipping? ' Yahoo Answers

https://answers.yahoo.com/question/index?qid...

Jul 17, 2012 - i have recenty purchased a reebok edge series 2.2 treadmill but when i run in it the belt slips foreward then carries on the way it ... I sounds like the belt needs to be tightened. ... Walking belt on treadmill slips under pressure?

If you have adjusted the tension on your belt to the max, it is more than likely time to replace your running belt. The running belt naturally stretches over time. I would suggest replacing the belt and flipping your deck. If the deck has already been flipped once, then you would need to replace the deck as well. Life Fitness Treadmill Belt and Deck Replacement Video 95T

Adjusting Tension on a Treadmill Running Belt It is necessary to properly tension a treadmill belt when it is replaced. After time, a belt can stretch and may begin to slip. When this happens, it is necessary to adjust the tension of the running belt to stop it from slipping. Manufacturers of treadmills generally agree on one of three procedures for how to tension a treadmill running belt.

1. Adjust for no slippage of the treadmill walking belt on the front roller (Often referred to as the "Stomp Test")
   1. This procedure works well for a previously installed belt that is now slipping.
   2. Underside of belt should be free of any glazing/wax buildup.
   3. Rollers must also be free of wax buildup.
   4. Be sure belt tracking/centering is correct before proceeding.
   5. The most popular speed for this adjustment is 2mph to 3mph.
   6. Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails. If the running belt slow, slips or stops (and the front roller does not) adjust BOTH adjustment bolts 1/4 turn clockwise. Test again and repeat adjustment if necessary.
2. This procedure requires two belt gauges or calipers
   1. This procedure works well when installing a new belt.
   2. This procedure requires you to stretch the belt. Depending on the manufacturer*, this varies between .4 and .6 percent. A dial on the gauge or caliper will indicate the amount of stretch. *Consult the owner/service manual for proper tension.
   3. If you are working on a previously tensioned belt you will need to release the tension before attaching the gauges or calipers.
3. Gauges or Calipers unavailable
   1. Release the tension on the belt.
   2. Using a yard stick or tape measure, place two marks on the left and right edges of the belt and deck 36 inches apart (or 50 inches if you prefer).
   3. Adjust the left and right tensioning bolts until both sides measure 36 3/16 inches (or 50 1/4). This is equal to .5% of stretch.
   4. Test for proper tracking and tension, adjust if necessary.

How to Tension Treadmill Walking Belt that Slips

Adjusting Tension on a Treadmill Running Belt It is necessary to properly tension a treadmill belt when it is replaced. After time, a belt can stretch and may begin to slip. When this happens, it is necessary to adjust the tension of the running belt to stop it from slipping. Manufacturers of treadmills generally agree on one of three procedures for how to tension a treadmill running belt.

1. Adjust for no slippage of the treadmill walking belt on the front roller (Often referred to as the "Stomp Test")
   1. This procedure works well for a previously installed belt that is now slipping.
   2. Underside of belt should be free of any glazing/wax buildup.
   3. Rollers must also be free of wax buildup.
   4. Be sure belt tracking/centering is correct before proceeding.
   5. The most popular speed for this adjustment is 2mph to 3mph.
   6. Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails. If the running belt slow, slips or stops (and the front roller does not) adjust BOTH adjustment bolts 1/4 turn clockwise. Test again and repeat adjustment if necessary.
2. This procedure requires two belt gauges or calipers
   1. This procedure works well when installing a new belt.
   2. This procedure requires you to stretch the belt. Depending on the manufacturer*, this varies between .4 and .6 percent. A dial on the gauge or caliper will indicate the amount of stretch. *Consult the owner/service manual for proper tension.
   3. If you are working on a previously tensioned belt you will need to release the tension before attaching the gauges or calipers.
3. Gauges or Calipers unavailable
   1. Release the tension on the belt.
   2. Using a yard stick or tape measure, place two marks on the left and right edges of the belt and deck 36 inches apart (or 50 inches if you prefer).
   3. Adjust the left and right tensioning bolts until both sides measure 36 3/16 inches (or 50 1/4). This is equal to .5% of stretch.
   4. Test for proper tracking and tension, adjust if necessary.

How to Tension Treadmill Walking Belt that Slips

Adjusting Tension on a Treadmill Running Belt It is necessary to properly tension a treadmill belt when it is replaced. After time, a belt can stretch and may begin to slip. When this happens, it is necessary to adjust the tension of the running belt to stop it from slipping. Manufacturers of treadmills generally agree on one of three procedures for how to tension a treadmill running belt.

1. Adjust for no slippage of the treadmill walking belt on the front roller (Often referred to as the "Stomp Test")
   1. This procedure works well for a previously installed belt that is now slipping.
   2. Underside of belt should be free of any glazing/wax buildup.
   3. Rollers must also be free of wax buildup.
   4. Be sure belt tracking/centering is correct before proceeding.
   5. The most popular speed for this adjustment is 2mph to 3mph.
   6. Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails. If the running belt slow, slips or stops (and the front roller does not) adjust BOTH adjustment bolts 1/4 turn clockwise. Test again and repeat adjustment if necessary.
2. This procedure requires two belt gauges or calipers
   1. This procedure works well when installing a new belt.
   2. This procedure requires you to stretch the belt. Depending on the manufacturer*, this varies between .4 and .6 percent. A dial on the gauge or caliper will indicate the amount of stretch. *Consult the owner/service manual for proper tension.
   3. If you are working on a previously tensioned belt you will need to release the tension before attaching the gauges or calipers.
3. Gauges or Calipers unavailable
   1. Release the tension on the belt.
   2. Using a yard stick or tape measure, place two marks on the left and right edges of the belt and deck 36 inches apart (or 50 inches if you prefer).
   3. Adjust the left and right tensioning bolts until both sides measure 36 3/16 inches (or 50 1/4). This is equal to .5% of stretch.
   4. Test for proper tracking and tension, adjust if necessary.

How to Tension Treadmill Walking Belt that Slips

Adjusting Tension on a Treadmill Running Belt It is necessary to properly tension a treadmill belt when it is replaced. After time, a belt can stretch and may begin to slip. When this happens, it is necessary to adjust the tension of the running belt to stop it from slipping. Manufacturers of treadmills generally agree on one of three procedures for how to tension a treadmill running belt.

1. Adjust for no slippage of the treadmill walking belt on the front roller (Often referred to as the "Stomp Test")
   1. This procedure works well for a previously installed belt that is now slipping.
   2. Underside of belt should be free of any glazing/wax buildup.
   3. Rollers must also be free of wax buildup.
   4. Be sure belt tracking/centering is correct before proceeding.
   5. The most popular speed for this adjustment is 2mph to 3mph.
   6. Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails. If the running belt slow, slips or stops (and the front roller does not) adjust BOTH adjustment bolts 1/4 turn clockwise. Test again and repeat adjustment if necessary.
2. This procedure requires two belt gauges or calipers
   1. This procedure works well when installing a new belt.
   2. This procedure requires you to stretch the belt. Depending on the manufacturer*, this varies between .4 and .6 percent. A dial on the gauge or caliper will indicate the amount of stretch. *Consult the owner/service manual for proper tension.
   3. If you are working on a previously tensioned belt you will need to release the tension before attaching the gauges or calipers.
3. Gauges or Calipers unavailable
   1. Release the tension on the belt.
   2. Using a yard stick or tape measure, place two marks on the left and right edges of the belt and deck 36 inches apart (or 50 inches if you prefer).
   3. Adjust the left and right tensioning bolts until both sides measure 36 3/16 inches (or 50 1/4). This is equal to .5% of stretch.
   4. Test for proper tracking and tension, adjust if necessary.

How to Tension Treadmill Walking Belt that Slips

Adjusting Tension on a Treadmill Running Belt It is necessary to properly tension a treadmill belt when it is replaced. After time, a belt can stretch and may begin to slip. When this happens, it is necessary to adjust the tension of the running belt to stop it from slipping. Manufacturers of treadmills generally agree on one of three procedures for how to tension a treadmill running belt.

1. Adjust for no slippage of the treadmill walking belt on the front roller (Often referred to as the "Stomp Test")
   1. This procedure works well for a previously installed belt that is now slipping.
   2. Underside of belt should be free of any glazing/wax buildup.
   3. Rollers must also be free of wax buildup.
   4. Be sure belt tracking/centering is correct before proceeding.
   5. The most popular speed for this adjustment is 2mph to 3mph.
   6. Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails. If the running belt slow, slips or stops (and the front roller does not) adjust BOTH adjustment bolts 1/4 turn clockwise. Test again and repeat adjustment if necessary.
2. This procedure requires two belt gauges or calipers
   1. This procedure works well when installing a new belt.
   2. This procedure requires you to stretch the belt. Depending on the manufacturer*, this varies between .4 and .6 percent. A dial on the gauge or caliper will indicate the amount of stretch. *Consult the owner/service manual for proper tension.
   3. If you are working on a previously tensioned belt you will need to release the tension before attaching the gauges or calipers.
3. Gauges or Calipers unavailable
   1. Release the tension on the belt.
   2. Using a yard stick or tape measure, place two marks on the left and right edges of the belt and deck 36 inches apart (or 50 inches if you prefer).
   3. Adjust the left and right tensioning bolts until both sides measure 36 3/16 inches (or 50 1/4). This is equal to .5% of stretch.
   4. Test for proper tracking and tension, adjust if necessary.

How to Tension Treadmill Walking Belt that Slips

see the video and proceed according. God bless you

It might just need a simple adjustment of the running belt that can eliminate the slipping refer to you owner's manual for the procedure. It will be close to all treadmill running belt adjustments.
Here is a generic procedure for adjusting the belt:
If the walking belt slips when walked on. Run the treadmill @ 3 to 4 mph, walk for a few minutes, Using the allen wrench, turn both rear roller adjustment bolts clockwise, 1/4 of a turn. Then repeat adjusting procedure until walking belt is properly tightened.

Since the drive pulley is slipping on the roller itself, then the front roller will need to be replaced.