On-Off switch stuck in the "Off Position" ? - Omega 1000 Juice Extractor

I just had the same problem with my juicer. Here's what I did to solve it. FIRST, UNPLUG IT!. Next, take all the accessory parts off of it. Then, turn the base unit upside down and shake it around a bit. Then put it back on the counter in the regular upright position and start jiggling the power switch back and forth. After I did this, the power switch started moving again.

I think this juicer is made in france, depending where you live parts may be hard to get , If ok when stored it may have stuck brushes or a corroded switch , ask for a written quote if you take it for repairs as it may cost more than a replacement.

The spout, itself is hinged. It has two positions, an upper and a lower position. (Similar to a light switch). Make sure it is in it's lowest position when making juice, otherwise the liquid will collect in the inner bowl and leak out the sides of the juicer. Move the spout to the upper position to temporarily stop the flow of juice, such as when you change glasses or receptacles. Then, put the spout in the lower position to resume the flow of juice.

If there is not a flaw in the product itself it could be a problem with assembly or that the locking bar is not locked in place properly. The juicer will not operate if the locking bar does not click in to place in to the grooves on both sides of the lid.

Jack LaLanne has several HowTo videos posted that would be worth reviewing:

http://www.powerjuicer.com/power-juicer-how-to-videos.php

You are also able to download a manual which includes illustrated assembly and disassembly instructions:

http://www.powerjuicer.com/power-juicer-manuals.php

If you are unable to lock the locking bar in place it suggests that some other component has not been installed in the correct position. Review the assembly instructions to make sure all pieces are properly positioned.

Thank you for using FixYa!

Just looked at mine because I thought there also might be an interlock switch
where the latch arms snap shut. There isn't one, at least on this one. Yours
might be a newer edition, so make sure the latch arms are fully seated and
snapped closed. You can also call Omega at 1 800 633 3401 and run it by
them. The reset switch should be in the pushed in position, it will pop out if
it's tripped.

The Operating Manual for the Power Juicer Elite is available here:

http://www.powerjuicer.com/pdf/elite.pdf

Check to make sure machine, including pulp collector is properly assembled; check silver bar is in upright position; check that spout is in downward position; preset reset switch located on underside of the main base.

For Tips and to view How To videos visit the website at:

http://www.powerjuicer.com/power-juicer-how-to-videos.php

this happens to me a lot. Take the lid off the juicer and turn the lid upside down take a hammer preferably a rubber mallet one and gently tap the bottom of the plunger while holding it upside down with bottom part of plunger up to your vision field tape it on bottom while trying to turn it into the right position (flat side to flat side) from the top putting a little torque on it..when it is tapped with a hammer or some similar tool far enough up the tube in reverse, it will then turn into the right spot if you tap the bottom with one hand while turning t to the right position on the top of the plunger and will be able to be removed but do not tap hard enough to break it.

First, check that the switch is in the on position. Then, check that all parts are assembled properly. The unit has a built-in safety device that will not let the motor turn on if not assembled properly. The Power Juicer also has a built-in Thermal Cut Off Safety Switch. If the machine was running, then shut down due to accidental overheating, then there is a 10 minute cooling time before the machine will restart. This helps to protect the motor from seizing. Click on the link below and select your juicer model to view the instructions and operating manual

http://www.powerjuicer.com/customer-manuals.html

Regarding Jack Lalanne juicer. After making sure nothing clogs the blades., make sure the stainless bar is on the correct slots on top of the juicer, left and right. It has a safety switch that when its not closed properly, it won't run.

lubricate all the switches by using the spray type lubricant or similar contact cleaner that would not leave any residue to contacts