When i restart my notebook...i get nothing...just a blank screen...nothing else...no curser...no BIOS entering...but web access without booting up is working. Help me please

Follow the steps below to configure the boot order on most computers.

1. Turn on or restart the computer.
   
2. While the display is blank, press the f10 key to enter the BIOS settings menu.
   NOTE: The BIOS settings menu is accessible by pressing the f2 or the f6 key on some computers.
   
3. Select the Advanced tab using the right and left arrow keys.
   
4. Use the up and down arrow keys to select Boot Order .
   
5. Follow the on-screen instructions to change the boot order.
   

Your hard drive is missing from the system. Or, just does not recognize it. The obvious - Remove any USB devices like drives and any media from disc player. Its trying to load, but can't find bootable hard drive, CD, or USB... Remove the hard drive and re-seat (reconnect). Check BIOS by pressing an F key during boot. Look on the screen for correct Function key. Might be F2 key. Verify BIOS recognizes the drive. It must be listed! There is no going forward if it's not. Check boot order and make internal hard drive first. Save and restart.

restart the laptop then at the time of booting press F8 / F2 then a screen shows and there shows " Last knwon good configuration " go over this select and press enter ur system will be boot .

If ur system not boot in this process then take backup and format the laptop.

press and hold f8 to reach your boot options menu, then select safe mode without networking. you may be automatically redirected to a windows repair utility. If this is the case, let it run, it will take a while to complete. The system will then restart itself and attempt to boot again. If this does nothing for your, try pressing and holding f12 on boot up and select the system repair/scan option. If all else fails, You can download and burn HBCD iso and run the partition recovery program. but you should be able to boot without it..

GOOD LUCK AND PLEASE RATE THIS POST!!!!

Restart your notebook and open it on safe mode...then use system restore or if you have installed an antivirus before it happens uninstall it..

may be a bios problem,,,go to hp website for support,,trouble shooting and drivers,,

your system maybe having a hard time accessing on your boot up drive, going into bios and setting up the hard drive with an operating system intalled on first boot may fix your problem.

Try to enter into bios by pressing Del or F2 or F10 ..while booting ..

Dear user,
if you are trying to access bios for setup of CD ROM as a first boot device and having problem to access the bios then here is an advice for you.

most of notebooks or systems have a special key assigned to select the boot device at startup without entering in bios setup. therefore please hit function keys at startup like F9,F11,F12 when you start system. F9 and F12 keys are most commonly used for boot device selection.

hopefully you will understand my advice.

Please dont forget to RAte my solution

This error message may appear when the computer BIOS is set to boot from a network and cannot find a bootable operating system on the network or on any of the storage devices included in the notebook PC's boot path.

The following steps are for most HP Pavilion and Compaq Presario Notebook PCs. The boot order can be configured on the Advanced tab in the BIOS settings menu. The steps to modify the boot order may vary depending on the model of your computer. On most HP notebooks the boot order can be configured using the following steps:

1. Turn on or restart the computer.
2. While the display is blank, press the F10 key to enter the BIOS settings menu. NOTE: Some notebook PCs use the F2 or F6 key.
3. Use the right and left arrow keys to select the Advanced tab.
4. Use the up and down arrow keys to select Boot Order .
5. Follow the on-screen instructions to change the boot order.

Reset the boot order to the default settings Use the following steps to reset the boot order to the default settings:

1. Turn on or restart the computer.
2. While the display is blank, press the F10 key to enter the BIOS settings menu.
3. Press the F9 key to reset the BIOS to default settings.
4. Press the F10 to save the changes and exit the BIOS settings menu.

I think it will you to fix your problem.
If still have problem then tell me more about it.

Thanks
Iqbal