Hi, few days ago I bought a Netgear NAS 2110 and connected it to my Netgear WNDR3700 router. I installed RAIDar utility and followed the instructions. Everything seemed to work alright. From my laptop I could copy files to NAS and everything still seemed to work as it should. Then I would like to switch off the server and I pushed the power button, but nothing happened. I tried again for 5 seconds and nothings happened. Then I tried again and it switched off. Next day I pushed the button to switch on again and the blue light started to flicker and after 2 hours it still hasn't connected and RAIDar utility cannot locate the NAS. The On/off button doesn't work anymore or at least I cannot turn it off. Could you please help me finding a solution on the problem with power switch and connection.

Try changing the channel.
you'll have to logon to the router - best to google the make/model for IP address etc.

you know what lets make this easy and not over think it. power cycle the modem. the modem paired your ip to the PC and now it needs its ARP table cleared so it can give the ip to the router.

The simplest way to add more ethernet ports is to use a network hub and connect it to the Netgear DG834 instead of the Netgear WNDR3700. This does not require any configuration.

You can download and print the manual from the Netgear WEB site.
ftp://downloads.netgear.com/files/WNDR3700_UM_16OCT2009.pdf

If it is this new I would suggest calling Netgear and have their support help you out. Due to the way their warranty works that would be best. I have a netgear router and hate it. I wish I had taken it back as soon as I had trouble. I also out sourced my problem and keep fooling with it, till it was to late to return it and the warranty ran out. Netgear is the hardest most difficult routers to deal with. May or may not work with AT & T DSL they will not tell you if that is the problem or not. Tell you it's your wireless phone or your neighbors who knows, In other words they do not know what causes these problems. Sorry for your trouble with Netgear.

Hi
Sometime the problem come from the powersupply itself the voltage drop under load causing weird troubles working for a internet provider and sometime we get weird trouble caused by bad powersupply

Hi,

you need to upgrade formware on router the reset and reconfigure router

following is the steps to upgrade firmware on router

link for latest firmware
http://kb.netgear.com/app/answers/detail/a_id/13091

A. Open the router page using the following way:
1. Connect a computer to the router using any one of the 4 available ports.
2. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
3. Access the router, usually by typing 'http://192.168.1.1' or 'http://www.routerlogin.com' in the address bar.
4. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
B. Visit the following link to download the latest firmware.
http://kbserver.netgear.com/prod
C. Please follow the steps to upload the firmware of the router:
1. Open the router page using the steps mentioned above.
2. Under Maintenance, click router Upgrade.
3. Click Browse and locate the upgrade file.
4. Click Upload.
5. Wait for the router to reboot.
6. Click on 'Logout' (at the bottom of the list) from left menu.
7. Reset and reconfigure the router.

RESET THE ROUTER:

1. Make sure router is connected to power supply and is on while you perform the task below. At the rear panel of the router, near the antenna, there is a very small round pinhole that contains the reset button.
2. Using a pen/pencil/paper clip, hold the reset button for 60 sec. so that the test light starts flashing.
3. After few seconds when the test light stops flashing. Turn off the router and turn it back on after a couple of minutes.
RECONFIGURE THE ROUTER:
1. Please remove all the connections from the router. Connect power to the router and then connect a cable from the computer into any of the 4 lan ports on the router. Make sure the modem should not be connected to the router or to the computer.
2. Open up the Internet Browser (Safari, Internet Explorer, Mozilla Firefox, Opera, etc.).
3. Put http://www.routerlogin.com/basicsetting.htm in address bar.
4. On the basic setting page scroll to the bottom and click on Apply.
5. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
6. Click on lan ip setup under advanced.
7. Change the lan ip to 192.168.10.1 and under use router as a dhcp server change the starting ip as 192.168.10.2 and ending ip as 192.168.10.51, click apply and click ok for any popup message that arise.
8. Once the browser display some error message like CANNOT FIND SERVER, ACTION CANCELLED etc, Connect the dsl modem on the wan port of the router and restart the computer.
9. Power off the dsl modem and the router after making the connections.
10. Power on the dsl modem and wait till the dsl light comes on, then power on the router.
11. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
12. Access the router (http://192.168.10.1).
13. Login to the router (Username = admin Password = Password).
14. Click on Setup Wizard and then select "Yes" and Click "Next" on the detection window.
15. It should give you a "Dynamic IP Detected" or "pppoe detected"(type the Username & Password of your dsl account in case of pppoe detection) and then click next.
16. Click Apply.
17. Logout of the router.
18. Open up another browser window and try to access internet.

Hope it can fix your issue
happy to help
Thanks for using Fixya

I would say that you should re-install the Western Digital My Book.

Hope this helps!

Hi, Please upgrade the RAIDar Software for NAS. You may download the same from the below link:

http://www.readynas.com/?cat=41

If the issue persists then please log a compalint with official NETGEAR support site at my.netgear.com

Regrds
Anand

Hi
firstly you can try upgrading the drivers on the adapter. following is the link for the latest drivers http://kb.netgear.com/app/answers/detail/a_id/12520

If the problem still persists
try changing the wireless settings on the wireless router.