How do I program my channels with a new universal remote?

Hello
You just buy one Philips Universal Remote control [MODEL NUMBER CL 034]. Symphonic is listed in its codes. Codes are: 0906 0520

Direct Code Entry

1. Press and hold the CODE SEARCH

button until the red indicator stays

on, then release the CODE SEARCH

button.

2. Press and release the desired Mode

button (TV, VCR, etc.). The red

indicator blinks, then stays lit.

3. Enter the 4 digit code from the code

tables. Note: after a valid code entry,

the red indicator turns off. For an

invalid code, the red indicator

flashes.

4. With your device on, press

CHANNEL UP. If the device

responds, no further programming is

required. Note: If some buttons do

not operate your device, try one of
the other codes for your brand.
OK.

ther is two things first verify the old remote with a IR reflecting card you can puchas at radio shack, or use a video camera to see the infraread LED flashing just to make sure it is dead, then check if the universal remote supports your TV

or the IR receiver on the TV could be defective, have it checked by a proffessional tech.

Programming a Living Solutions Universal Remote
1. Step 1 Turn on the component you wish to sync to your universal remote--your television, DVD player, VCR or stereo.
   
2. Step 2 Point the remote at the device you are programming and press the corresponding device button on the remote. These buttons are labeled "TV," "VCR", "DVD," etc. Hold the device button for three to five seconds.
   
3. Step 3 Push the power button on the remote. This should turn on the device that you are syncing.
   
4. Step 4 Push the "Channel Up" or "Channel Down" button on your remote gradually until the device that you are programming shuts off.
   
5. Step 5 Press "OK" or "Enter" on the remote once the synced device turns off.
   
6. Step 6 Press the device button for the component you just programmed, and hit the power button while pointing the remote at the component. If programmed correctly, the device should turn on, and you should be able to control it with your Living Solutions Universal Remote.
   

Hello, on some of these combinations you might have to try not only the TV codes on your universal remote list, but also the DVD or VCR codes also. One of these three will program your universal remote, but make a note: you may have a partial function on your remote ie: power, but no volume control or channel scan(up/dn) or no number operation(0-9). This happens on some of the universal remotes not all of them. thanks!

u can go 2 buy a universal remote with a handbook 2 tell u how 2 program it lol.b alot easier.that way if u have dvd & vcr...it can b programmed 2 operate it as well as the tv!universal remotes r the best sollution lol.lazier the better lol.

usually has to be on channel 3 then use the tv/vcr button on your remote.if you are already using this for a vcr then you need to program the dvd on another alternate.Best results is to get a universal remote and program tv/vcr/dvd seperate.

To see RCA's code list you probably need their website but Emerson is one of several names now owned and built by Funai, who also builds Symphonic & Sylvania. 
You might want to try those codes with your set.  

scroll down on the channel button from channel 2. the different aux inputs should be there.there may also be a video/line in/source button on the front of the tv.if there isn't, you can buy a cheap universal remote for under $10 [even in some dollar stores for $1]
wg

This set doesn't have that option...accordianman

First of all try getting a Symphonic remote - http://www.miracleremote.com/ not that expensive. Then you can access all areas of the TV, including all sub menus and see how the audio is set-up.. Could be you have it in SAP mode, (Second Audio Programming), in which case you will hear nothing...
Bill