I ahve forgotten my forgotten netgear password on WGR614 router. Please advise Thanks Tony

have you tried logging into the router's setup page to reset it?

If you cannot log into your router because you have forgotten the router password or your network has been hijacked, please refer to "Lost or forgotten password for router or other device" below.
1.Connect your computer to the router with an Ethernet cable .2.Log in to your NETGEAR router by browsing to http://www.routerlogin.net or http://www.routerlogin.com. Enter the username (admin) and password. By default, the password is password or 1234 unless it has already been changed.3.From the left-hand navigation menu of the Router Manager, select Set Up > Wireless Settings.From the center screen, select your encryption type from under the Security Options heading.
If the wireless network passphrase is visible, review it and use it to log devices onto your network.If it is not visible, you can change your wireless passphrase;
If you cannot log into your router:
Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.
NOTE: Restoring factory defaults on a device will erase any customizations you have made. You will lose any configurations saved to the device!
To reset the password /router follow the steps below:
Press the reset button on the back until the test light blinks. This takes about 10 seconds. (To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)Release the button.Wait for the router to reboot.Log in with the default password.If the router configuration was not cleared, try these additional steps AFTER the router has finished rebooting.
Unplug the router's power.Press and hold the reset button. While the button is held down, reconnect router's power.Continue to hold the reset button for 20 seconds after reconnecting the power.Wait for the router to reboot.Log in with the default password.
For more information see the link below:
http://support.netgear.com/app/answers/detail/a_id/9665

Also refer to router's users manual >The manual is available online >Click this link ->http://support.netgear.com/app/products/family/a_id/1296
Select the right WGR614 >>Next click Documentation > click on the router's setup manual to start downloading ..
Please let me know if you need further assistance on this issue .

1. Push the "Default Reset" button on the back of the Netgear WGR614-V6. The button is located on the back of the unit, to the left of the external antenna. You may need to use a pin or the tip of a pencil to access the button.
   

2. 2

   Continue holding the button in until you see the "Power" indicator on the front of the unit turn off and back on. This takes approximately ten seconds.
   

3. 3

   Let go of the button. The Netgear WGR614-V6 shuts off and turns back on. Allow several seconds for this process to complete.
   

4. 4

   Log into the router using the default password by opening a Web browser and navigating to the address "192.168.1.1." Enter the password "password" to log in.
   

Read more: How to Reset the Password for Netgear WGR614-V6 ' eHow.com http://www.ehow.com/how_6500350_reset-password-netgear-wgr614_v6.html#ixzz199K9aGLg

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

If you have forgotten the login password, you can reset the Netgear back to the default settings by power up the Netgear and press and hold the pinhole RESET button at the back of the router until the LEDs flash.
The default login = admin
the default PW = password

If you can log onto the router @ 192.168.1.1 with the user name:admin- password: password

then you can go to the Wireless tab, then security. There you will see you key.

If not you need to reset the router:

Push the "Default Reset" button on the back of the Netgear WGR614-V6. The button is located on the back of the unit, to the left of the external antenna. You may need to use a pin or the tip of a pencil to access the button.

2

Continue holding the button in until you see the "Power" indicator on the front of the unit turn off and back on. This takes approximately ten seconds.

3

Let go of the button. The Netgear WGR614-V6 shuts off and turns back on. Allow several seconds for this process to complete.

4

Log into the router using the default password by opening a Web browser and navigating to the address "192.168.1.1." Enter the password "password" to log in.

Read more: How to Reset the Password for Netgear WGR614-V6 ' eHow.com http://www.ehow.com/how_6500350_reset-password-netgear-wgr614_v6.html#ixzz15Vaa7ANz

Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response.

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Connect to the router by typing
http://www.routerlogin.net in the address bar of a browser.
if it asks for the id and password enter
id = admin
password = admin or password or leave it empty

go to Wireless Settings and Change the Channel using the drop down box. Save the settings.

You will need to connect to the router and set up WEP. Do you know the Admin password for the router?

When you look on the box that the router came in, you have to look to see what Operating Systems it is compatible with. In many cases, routers will not be compatible with vista. I have a Linksys WRT300N, and it works great with Vista.Hope this helps.

Hi!

Try these:

1. Go to CONTROL PANEL > MANAGE WIRELESS NETWORKS
2. Remove all the preferred networks
3. Restart your laptop
4. Reconnect to your network

Hope this helps!

try using "admin" for the user and "password" for the password. I have this very same router and that was the default settings for me.