Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

1 Answer

I have fault code F06 on my Hotpoint WMf740 machine, what does this mean?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 168 Answers

Hello,

F6 error is apparently a motor fault. The
motor could be jammed, open circuit ,
burnt out. It may just be a broken wire
or connection come off. Check the motor.

Posted on Apr 21, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jsrock516
  • 5911 Answers

SOURCE: f06 error code on Whirlpool duet washer

An explanation of your error code can be found at the following link:

http://www.fixya.com/support/r714929-f06_error_whirlpool_duet_kenmore_elite

In a nut shell, usually one of the motor windings fails, causing the Drive Motor to not rotate at the correct rpm, or not at all. Or, the Motor Control Unit fails. Both are simple repairs and can be accomplished by the average do-it-yourselfer. If you wish to attempt this repair, let me know and I can give you the steps required to complete it.

These parts can be found at searspartsdirect.com. Just type in your model number and look under the "Pump and Motor Parts" heading on the next page. The MCU will be listed as item number 1 (part #8181693). The Drive Motor is listed as item number 16 (part #8182793). You can also try repairclinic.com, pcappliancerepair.com, and partsstore.com for comparative pricing. If you require further assistance, please let me know.

Posted on Jun 28, 2008

barkencoa
  • 3463 Answers

SOURCE: Hotpoint Aquarius WT740 Fault Code

Hi. F05 means pressure switch jammed on full.
Check pump for blockage and that it is working, if no joy you will have to call an engineer
.

Posted on Nov 20, 2008

jsrock516
  • 5911 Answers

SOURCE: whirlpool awo3561 fault showing as f06? what does

"F06" is a Motor Speed error code. It means the motor is not spinning, or you have a loss of commuincations between the Motor Control Unit (MCU), Central Control Unit (CCU) or Drive Motor. The following link explains:

http://www.fixya.com/support/r714929-f06_error_whirlpool_duet_kenmore_elite

The easiest place to start would be to verify all your connections between the Drive Motor and MCU are intact and not corroded. Then, perform resistance checks on the Drive Motor windings.

For ease of troubleshooting, UNPLUG the washer and remove the top panel by removing the three screws that hold it in place in the rear of the washer. With the screws removed, the panel will slide back, then off. Position the washer where you have full access to the rear. Remove the back panel of washer. With the top and back removed you will have full access to the CCU, MCU and Drive Motor.

If you have questions along the way, or if you require addtional assistance, please let me know. I hope you find this information helpful.

Posted on Mar 05, 2009

barkencoa
  • 3463 Answers

SOURCE: Hotpoint WD860 - Fault Code F-07

F07 indicates heater relay stuck.
You need to check the heater to see if it is faulty, and fit new one if it is.
Please rate my solution.
Thanks.

Posted on Jul 10, 2009

  • 5 Answers

SOURCE: hotpoint ultima washing machine is showing a fault

F 05 normally means there is a blockage or a fault with the pressure sensor. The common place for blockage is in the black pipe from the drum to the pump as it has a filter in here and clogs up. remove the pipe and clean the filter out and remove gunk from the pressure sensor on the side of the pipe as well. If that does not fix things the pressure switch could be faulty itself

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a hotpoint ultima wf860 it was all fine then all of a sudden its saying the error code f-18 how can I fix this please as I havent enough money for a newone yet. many thanks x


Hi, The link below is a user manual for a hotpoint ultima wf860 and below that are the error codes, I wish you all the best......CHEERS...

file:///C:/Users/Steve/Desktop/4992cbf9-f956-4127-bdab-caa958e02377.pdf <---"NEED TO COPY AND PASTE"

Hotpoint Washer Error CodesF01 - Electronic circuit board fault
F02 - Motor circuit fault
F03 - Temperature sensing fault
F05 - Waste pipe blockage or pump issue
F06 - Door lock fault
F07 - Electronic circuit board fault / heating circuit fault
F08 - Heater fault
F09 - Software fault
F11 - Pump circuit fault
F12 - Electronic control fault
F13 - Dryer temperature sensing fault (washer dryers only)
F15 - Heater control fault (washing machines and washer dryers)
F16 - Drum lock position sensor fault (top loading machines only)
F18 - Internal data error
F19 - Fan motor or heating fault (washer dryers only)

Apr 01, 2016 | Hotpoint Washing Machines

1 Answer

What is error code F06


The "F06" fault code indicates a drive motor error. This means the control is unable to properly detect motor speed and the machine will shut down.

Mar 17, 2016 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My hotpoint aqualtis model number aq9f 492 u is showing f6 what does this mean


F06 Door lock fault
Issue: Washing machine door cannot be opened or closed / when the door is closed the machine the programme will not start.
Advice: If your washing machine door will not close, please check for any obstructions in the door lock.

Dec 29, 2015 | Hotpoint Washing Machines

1 Answer

Hotpoint aquarius super silent WF630 FAULT CODE F02


[/spoiler] [spoiler title="EVO1 Washing Machines and Washer Dryers" open="0" style="2"]
  • F01 - Short circuit motor triac*
  • F02 - Motor jammed tacho detached*
  • F03 - Wash thermistor open/short circuit*
  • F04 - Pressure switch jammed on empty*
  • F05 - Pressure switch jammed on full*
  • F06 - Program selector error*
  • F07 - Heater relay stuck*
  • F08 - Heater relay cannot be activated*
  • F09 - Incompatible eeprom*
  • F10 - Pressure switch not sensing correctly*
  • F11 - Pump cannot be activated*
  • F12 - Communication error*
  • F13 - Dryer fan or dryer thermistor faulty*
  • F14 - Dryer element faulty*
  • F15 - Dryer element relay faulty*
  • H20 - Not fillings. Check tap, hose and inlet valves
  • LOCKED - Check interlock*

Error Codes Hotpoint Service

Aug 24, 2015 | Hotpoint Washing Machines

2 Answers

How do you fix a fault F06 on a Whirlpool front loader washing machine


The "F06" fault code indicates a drive motor tachometer error. This means the control is unable to properly detect motor speed and the machine will shut down. If the failure occurs during high-speed spin, the door will unlock after 3 minutes. Possible Causes/Procedure: Unplug washer or disconnect the power supply. Check the wire harness connections between the motor and motor control unit and the harness connections between the motor control unit (MCU) and the Central Control Unit (CCU). Based on your symptom and details, the intermittent (F06) error code is likely a loose connection in the harness between the motor and the (MCU) or between the (MCU) and the (CCU). It could also be the tachometer circuit in the motor or an intermittent internal component connection within the (MCU). Since the (CCU) has already been replaced, the failure is likely a loose harness connection or the (MCU). I recommend calling the repair person back out to re-diagnose the failure. by Joey S MARCH 1ST, 2010 ' Be the first to comment

Jun 14, 2014 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Could someone email me the fault codes for a hotpoint aquarius wmf740 washing machine please


Hi I see you need the Fault Codes for your Hotpoint Washing Machine

See this link for the info since I do not have your E-mail to send the details I have created this link for your viewing regarding your concern.

Hope this helps.

Oct 02, 2012 | Hotpoint Washing Machines

2 Answers

Indesit 123 FAULT F06


I had this error and engineer said the meaning of the codes on the web are wrong as they don't like to disclose their real code meanings for pure protectionism reasons. F06 on IWD7145 is a burnt out door interlock IDC error. He replaced the part number C00085194 (replacement door interlock) and microritardator part number 085194 and it works ok now.

Sep 06, 2012 | Indesit W 123 Front Load Washer

1 Answer

I have a hotpoint aquarius wmf740 that is showing a fault f--5 and wont empty out the water


Something wrong the pump would prevent the machine draining and generate an F5 code.

http://appliancejunk.com/ge/washer/31-9103.pdf

Service manual above.

Jun 25, 2010 | Washing Machines

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

Related Topics:

2,143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

Eric Taylor

Level 3 Expert

590 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...