How i can add ip??? - 3Com WX4400 (662705485065)

You cannot add it manually...you can switch OFF and ON the device and again try the internet source like Wifi etc...If it gets connected..visit Ip-details.com and get the Ip address.

Hi,

How to create an IP address into your Printer
1, Connect to LAN network
2, Power ON the Printer.
3, Select MENU Button
4, Go to System Settings, then select Network Settings.
5, You can see TCP/IP , View IP ,etc.....
6, Type Your Printer IP address, Subnet Mask, GateWay, etc...
7, That's All......
In different Printer settings will be different.
Now You can add printer into your computer

Go to Control Panel--> Hardware and Sound -->Device and printers -->Add Printer-->Add network Printer-->"If no printer were found" Select "The printer that i want isn't listed" --> Add printer using TCP/IP--> Type your Printer IP address--> Now you can install printer software...

Thanks

It may not be accessing the IP for you friend you may want to use his or her email or username for messenger instead of his or her IP I have not ever heard of using a IP address to add a friend. I could be wrong here. Thanks for using FixYa! John

put the printer on
connect a straight cable from printer to your switch in network
now read the instruction manual the default ip is written over there
note it
now from any system in network
open network connections click on properties
goto tcp/ip
click properties
click advance
in tab-ip setting add any other ip of same class which was printer's default ip
ex- if printers ip was 192.168.0.1 add 192.168.0.7
now apply all settings
now on the same computer type the printers ip in any browser
this will give the access of printer to you
change ip setting according to your network class
i.e. assign the printer your network class ip
now you can access the printer from any system in network
do one thing that put drivers of printer in some sharable drive on the network
now you can goto any system add printer from control panel
select network printer
select the printer

when prompted provide location of drivers of printer
you are done .

for networking take the configuration page & note down the default ip add then open the internet explorer & note down the default ip & enter you will conect the printer directly then change the ip add as per ur requirement & uncheck the dhcp .

hope ur problem will be resolve...

Add the printer in a TCP/IP port and assign it that IP address. /Add Printer/local connection then set it to TCP/IP port and the printers ip address.

Hi,

You may want to try:

• If both your router and modem have DHCP features enabled, disable the one in the modem;
• manually set the Internet/WAN IP add of the router to follow the IP add of the modem;
• manually set the default gateway of the Internet/WAN side of the router to use the IP add of the modem;
• set the PCs connected to the router to automatically obtain IP adds.
• verify that the PCs uses as their default gateway the IP add of the router.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Let me know the settings of your Router if needed IP address?
Yes - add your IP address into Network Connection.
No - obtained the setting in your Network Connection.

How to Add or Obtained the setting s of your IP address:
- goto Control Panel
- Double Click Network Connection
- Rigth Click then Properties the Local Area Connection
- Select Internet Protocol (TCP/IP) and select Properties
- Under General Tab they have choices to add or obtained settings.

TCP/IP printing for windows xp:
you must know the IP address of the print server and the port name.and the pc's ip address must be in the same subnet as the print sever's ip address.
Step 1 Go to Start > Settings > Printers and double-click the Add Printer icon to open the Add Printer Wizard.
Step 2 Select Local Printer and click Next.
Step 3 Select Create a New Port and choose Standard TCP/IP Port from the drop-down menu and click Next.
Step 4 This will bring up the Add Standard TCP/IP Printer Port Wizard. Click Next.
Step 5 Enter the IP address of the print server and the port name and click Next.
Step 6 The next window will prompt you for the Device Type. Select the Standard radio button and use Generic Network Card from the drop-down window.
Step 7 Click Finish to close the port configuration wizard.
Step 8 This will bring you back to the Add Printer Wizard. Step through the remaining windows of the Add Printer Wizard, accepting the default values to complete configuration.