A grey screen is on my computer with a bunch of codes on it, I cannot get to any other screen. Along with it is a black box saying I need to restart my computer, when I do and turn it back on the same screen appears.

Gidday Mate this link might help you along there with the 1000
plus google up the wiring diagram pictures also.

1 Yamaha-fzr1000 89 Service Manual - Scribd

https://www.scribd.com/doc/.../1-Yamaha-fzr1000-89-Service-Manual
Hope that helps you along there Jeremy.

That is a kernel panic, your OS is corrupted, and you can repair the disk by booting off your install CD, or by reinstalling the operating system

Ok get ready for this, you have a PRAM battery on the motherboard, since your system is old the battery is dead. It is the same as a CMOS battery for a PC. It hold crucial startup info. Open the case replace the battery (can be bought at any radio shack) Press the reset on the mob and start from cd and set date and time then restart.

Two possible things are wrong either your hard drive has gone or your system has corrupted. Put your instal disk in start it up holding down the c key. Once it has started check that the hard drive exists by go to the menu bar and selecting the disk utility. If the hard drive shows it means that it is okay run the disk utility check drive and then run the repair permissions. Then try restarting, if it works then you are back up and running again. If the drive shows up and you restart and the same thing shows up with the grey screen, you will need to reinstal your system. You do this by starting up with the instal disk holding down the c key and run the instal script. To keep your hard drive contents your will need to use the preserve users instal.

If your hard drive does not show up the hard drive is probably a gonner and you will have to purchase a new hard drive and instal a fresh system.

Hope this helps

You have to ask the dealer or the former owner of this phone about the security code.

we need to restart the computer in safe mode( press f8 keys a few times right after restarting the computer). log on to the admin account...on desktop screen click start button > click run > type msconfig > click ok > you will get system configuration utility screen on the top right of that window there is a tab start up > click it and click disable all click apply and ok..restart the comp..
if it works well and good otherwise after clicking on disable all under start up tab > there is a diff tab next to it called services > click that on bottom left you will get a check box that says hide all microsoft services > check that box and click disable all> apply> ok> then restart the computer it will work
if not > then you need to re install the operating system

This belt light is a feature put on by kawasaki for safety. It'll continue to come on after it get so many kilometers on it. The light has to be reset in order to get it off. Now if your mechanically inclined i'll explain to you how to get that light to go off.

First thing you have to do is reach down under the right side of the bike and in under the side cover you'll find two black plugin and two grey pluggins. Unplug those two and then plug a black and grey together and then the other black and grey together. Then down on the belt box you'll find a square black metal box with two wires coming from it. Unplug that ****** also. Once you have this all done now turn the ignition key to the on position and wait for about 7 to 10 seconds and the computer will reset itself. After you do that, turn the ignition key off and then unplug the two black/grey connectors and plug them back together, black to black, grey to grey. Then plug the connector from the black metal box on the belt cover back in. After you have this done. Turn the key on and let it go thru it's cycle. When you are done the belt light should be off.

Now if after you have done all this, and the belt light remains on and you still have no power, then you have a switch problem in the belt box. You can either remove the belt box and check the switch inside of it to see if the switch has been tripped to off. If it has, then in all probablity you need to install a new belt and reset the switch. Personally, i'd cut the two wires coming out of that metal box i previously told you about and join then together on the bikes wiring harness side. Leave the two wires from the black metal box like they are. You don't have any warranty on that part of the bike anyhow, so why bother have that switch continue to cause you problems. In order to get the belt light to off after you cut those two wires is you'll have to go thru the process i explained to you before. Only this time at the end instead of plugging the switch wires back together, just twist the two wires on the harness side together,in theory all you are doing is plugging that plug together, only your disconnecting that switch and never again should it bother you. However, after a few 100 kilometers you may have to do all i explained to you over again, only the next time you'll have to untwist the two wires along with the two black and grey wires and then go thru the process again. After the process is done, replug black to black, grey to grey, and then twist the two wires back together, turn the key on again and let it reset itself. Again your belt light should be gone out.

Good luck
Wayne

Hello yoyoxide.


from my experience can be something related with the video card. I recommend you the followig (Hardware diagnostics):

-Look for one of the discs that came with your computer, it should say (Drivers & utilities).
-Boot from the CD. If you don't know how to do it do the following:
1.Insert the Drivers&Utilities Disk.
2.Restart teh computer.
3. When you get the Dell logo, press F12
4.Select Boot from CD/CDRW-DVD (something like that).
-You will get a prompt to run the diagnosics.
-Just follow the wizard
-I recommend you to run diagnostics for everything.
-You will see if you have any problems with your hardware.

It seems that you have a pretty new laptop, so probably it's under warranty.

my monitor says desact monitor and I dont know what it means.

If the screen then turns to black and says in a bunch of different languages, and a code that says E 62, then basically what you have to do is to take out the disk, and wipe it inside out with a soft cloth. A smooth inside to outside motion, BUT NOT and inside to outside and back to inside motion, ect. And then restart it again.