How to record an outgoing message on Radio Shack answering machine, cat. no. 43-3825, serial number 40318384.

ready complimentary where it is needed for a customer to earn acquisitions. CreeHack FAQs To Install the Creehack Apk on your Android Device.

To put the message in a specific mail box, the caller needs to press *1, *2 or *3 (touch tone phone) before leaving their message. (Of course the answering system has to pick up before the key stroke.) Obviously the number corresponds to the mail box that will get the message.

So if you want to include these directions in your outgoing message, you would need to add something like "To leave a message for John press Star 1, for Sam press Star 2" when you record the ogm.

The manual for the answering system is available from Radio Shack. See http://www.radioshack.com/product/index.jsp?productId=2257360#tabsetBasic . The direct link to the English version of the manual is http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/4303829_PM_EN.pdf .

I hope this helps.

Cindy Wells

To use your system from a remote telephone, you must first enter a 3-digit remote operation security code. The security code label is located on the bottom of the system.

1. Dial your phone number.

2. When your outgoing message is playing, enter your remote operation security code. Bd appears on the display to indicate the system is in remote mode.

If there are no new messages, you hear three beeps.
These are the remote codes available to you:

2 # Play all messages.
2 5 Play new messages.
3 # Delete all old messages.
7 # Record new outgoing message.
7 # Stop recording outgoing message.
8 # Record memo.
8 # Stop recording memo.
9 # Turn system off/on.
0 # Monitor the room..

You can download the manual at
http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/4303829_PM_EN.pdf

Recording Outgoing Messages:


1. Hold the ANNC-DAYand speak clearly into the microphone.

2. Release the ANNC-DAY when you finish. Your answering machine beeps and automatically plays back your recorded message.

Message limit:
60 seconds

To re-activate pre-recorded message:
Press "delete" during while playing your outgoing message. The pre-recorded message is now activated.

The "recording outgoing messages" section is the first thing on the second page of the manual at
http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/4303829_PM_EN.pdf

The "recording outgoing messages" is the first thing on the second page of the manual at
http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/4303829_PM_EN.pdf

The "recording outgoing messages" section is the first thing on the second page of the manual at
http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/4303829_PM_EN.pdf

Well, your machine might be broken, or you haven't set the little switch on the unit to ANS. The switch is on the side of the machine where the cables come out. But here are the instructions from the manual:

Recording Outgoing Messages:

Your answering machine has a built-in outgoing message, "Hello, please leave a message after the tone." You can use this message or record your own.

1. Hold the ANNC/DAY/<<, and speak clearly into the microphone, no more than 10 inches away.

2. Release the ANNC/DAY/<< when you finish. Your answering machine beeps and automatically plays back your recorded message.

*Your outgoing message must be between one and 60 seconds.

*If you record your won message but wish to revert to the pre-recorded message, press DELETE during playback of your outgoing message.

To Record Outgoing Message on Radio Shack’s Answering Machine [Model 43-3829]:

Press and Hold the ANNC/DAY/<< button. You’ll hear a beep; continue to hold down the ANNC/DAY/<< button and record your message. When recording of your [outgoing] message is complete, release the ANNC/DAY/<< button. Your message will automatically play back for you.

Please let me know if you have additional questions. Thanks!

Take care,
Gail :-)