Copy light flashes red. When I press on it it turns green. When I press start, copy light blinks green, there is a message 'warming up" and nothing happens. Printing from computer is fine.Printer is a HP psc 950.

try cleaning the disc and reload. i have that problem too. If it's a dvd recorder your disc might have a chip in it which thinks you are trying to copy it . try it on another dvd player without a recorder cability

• Turn on laptop.
• Laptop will be start booting. Red/yellow light will be blinking. If yes then check your monitor light will be fixing and Show *********** Board.
• If shows and your OS will be Booting and fail to start.
• If yes you can repair it.
• Insert OS disk into the DVD driver.
• Turn off PC.
• Turn on
• "Press any key........" when comes this message you press any key.
• After that you can see two option

?? Fresh copy Installation OR

?? Repair Option

• For Repair Press "R"
• It will be start repairing

• Turn on CPU.
• CPU will be start booting. Red/yellow light will be blinking. If yes then check your monitor light will be fixing and Show *********** Board.
• If shows and your OS will be Booting and fail to start.
• If yes you can repair it.
• Insert OS disk into the DVD driver.
• Turn off PC.
• Turn on
• "Press any key........" when comes this message you press any key.
• After that you can see two option

?? Fresh copy Installation OR

?? Repair Option

• For Repair Press "R"
• It will be start repairing

Thanks.

Try to check the Print Cartridges if they still have ink in them. or try to do a Semi-Full Reset. combo would be: - "print photo" + "red eye removal" buttons pressed together - printer will not ask you to enter the combo - release the buttons you pressed then - press "red eye", "print photo", "red eye" in sequence - scroll down or right until you find resets menu - press ok - scroll down or right until you find semi-full reset - press ok
- your printer should turn off, wait for 3 minutes before turning the printer back on

Hi,
please follow the steps given below to power cycle and reset the product.

Perform a power cycle

1. Turn the product off.
2. Unplug the power cord from the product..
3. Wait 30 seconds, and then connect the power cord to the product.
4. Turn the product on.
5. Make a color copy by pressing the Start Copy Color button on the control panel.

• If the copy job is successful, you do not need to continue troubleshooting.

Reset the product Follow these steps to reset the product. Step one: Perform a partial reset

1. Disconnect the power cord from the product.
2. Press and hold # and 3 while reconnecting the power cord to the product, and then release both buttons.
3. Try making a color copy by pressing the Start Copy Color button on the product control panel.
   • If the partial reset resolves the issue, you do not need to continue troubleshooting.
   • If the error message displays again, proceed to the next step to try a semi-full reset.

Step two: Perform a semi-full reset CAUTION: Performing a semi-full reset deletes any saved phone numbers on the product.

1. Disconnect the power cord from the product.
2. Press and hold # and 6 while reconnecting the power cord to the product, and then release both buttons.
3. Try making a color copy by pressing the Start Copy Color button on the product control panel.
   • If the semi-full reset resolves the issue, you do not need to continue troubleshooting.
   • If the error message displays again, proceed to the next solution.

Thats an error code, but I will need the model number to help you identify what the 5 blinks mean

the clear key may be stuck which seems to lock up your machine. The procedure to reset the drum lite is clear, auto (exposure setting), clear, auto when hit in a timely manner the display will go blank. Enter 24 then press the start key, then enter 07 and press the start key again. If you can't get the keys to work the circuit board may have cold solder joints.
Good luck

Bob

If you turn off the printer and turn it back on, do you get any noises, ie motor noises, or does it instantly go to all lights flashing?
If you get no noises this usually indicates a board fault and you should look for a new printer.

OK guys quite a simple one....

with the printer on press & hold both the small red button ( far right ) and the green, colour copy button. Whilst still holding press the power button wait till the unit powers off. Press the power button again, shortly after the unit powers on, the lights flash, let go of the two buttons your holding. The screen shoul dnow say "Init EEPROM" if it doesn't repeat procedure till it does. Now press the green colour copy button once, screen should now say "Push power sw" Press and hold the power button, the unit will power off and on again, now release the power button and your printer should be working again. Now you should change your waste pads......

Hi, The owners manual says that if the red light is flashing, it is an indicator that it is ready to be turned on (use remote or onboard on button); flashing red & green - too high temperature inside, the unit is overheated. Check and clean the air filters; If the red light is steady, abnormal condition and you have to call for service. A copy of your manual is available at http://www.eiki.com/resources/resourcedownload.ashx?filename=/ownersmanuals/om_xb25_20_sb20.pdf Hope this be of some help. Pls post again how things turn up. good luck and kind regards.