Question about Computers & Internet

1 Answer

Full tank so what can i do - Computers & Internet

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 10,406 Answers

> full tank, so what can I do?

Are you saying that the ink-cartridges in your printer are full, and that your ink-jet printer is still not printing?

If so, use the software that came with the printer, to run a "print-head-cleaning" cycle,
to "unclog" the ink-jets that pull ink from the tank and shoot the ink onto the paper.

Posted on Nov 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas tank will not fill up on 2001 ford expedition


Gas as in gasoline or gas as in LPG gas? If its petrol, the fuel sender may be out of adjustment. (Usually means a new sender) If its LPG, the fuel stations are set to automatically shut off at 80% full. The gas tank will never actually be full to the brim but the gauge should be showing full if the gas nozzle keeps shutting off. Have a look on the LPG tank itself, they have a little gauge on them which shows how full it is. I have 2 tanks on my car , when "full" or when the pump shuts down, the tank gauges show just under full but the gauge on the cars dash shows full (2005 BA Ford)

Feb 18, 2015 | Ford Expedition Cars & Trucks

1 Answer

Hi I have problems with my mitsubishi dehumidifier Oasis Elite MJ-E-142NX-A1 The water tank full light stays on even though the tank is empty. I have emptied the water and replaced the container care


Sounds like your float is stuck in the full position, or the sensor that shows full is stuck on full.
If tank is empty but shows full, problem lies where full signal is coming from.

Aug 19, 2014 | Dehumidifiers

1 Answer

When i am trying to put a full tank of gas it stops pumping when it's not full


Assuming your gauge is accurate, if the tank is not taking gas it usually has a restriction in the neck or a venting problem.
Any chance your tank is full and the gauge is off ?

Jul 02, 2012 | Cars & Trucks

1 Answer

Fuel gage goes from full to emty all the time. when it first stated it only did it with quater tank or less.


Sounds as if the SENDING UNIT in the tank is faulty. They work by RESISTANCE, so when the contacts on the fuel guage sending unit in the tank get worn, it will send incorrect data. Typically it will say full when the actually IS full, then, when the tank is 3/4 full, it will say EMPTY, and then, as you use more fuel from the tank, the guage will go from what is REALLY in the tank, to empty, at different times.

Only solution is to remove the fuel tank, and replace the sending unit guage assembly.

Jun 11, 2011 | Oldsmobile Aurora Cars & Trucks

5 Answers

I have a samsung clp500 color printer but it is not working .it show only waste tank is full/ not instaled what should i do.


The "waste tank" is located behind the front panel that has the SAMSUNG name on it. Press on the upper corners of this panel and it will open up to reveal a clear plastic tank on the right side.

This tank pulls out easily and has two holes for excess toner to flow into it.

Look at the side of the tank that has the holes. You should see a part of the tank that extends out from the tank but ends in a clear square. The waste tank sensor "looks" thru this clear plastic square to determine if the tank is full. I.e. if toner is in this area and you cannot clearly see thru both sides, the sensor will tell the printer that the tank is full and needs to be changed.

If the tank is not full, use a long cotton swab and clean out the inside of this area. Once you can see thru both sides, carefully replace the tank back into the printer and turn the printer back on.

If done properly, the error should go away and you should be able to continue printing. I have doen this and it works fine.

(Some posts have had people cut this part of the tank off and simply tape over the hole that is made with strong tape. This bypasses the sensor and would allow the printer to run again. I have not done this as I do not want the possibility of toner spilling in my office.)

Exception:

The sensor could be bad and causing the issue. If this is the case, it may be cheaper to purchase a new printer - CLP-620 ND is a duplex, networked color laser jet that is selling from frys.com for $315.

Apr 30, 2010 | Samsung CLP-500 Laser Printer

1 Answer

Indicator says "tank full"


The switch is the most likely problem,check the switch with a multimeter

Apr 03, 2010 | Amana D545M Dehumidifier

1 Answer

Tank absorber full and lights blinking


The POWER Lamp Flashes Orange Eight flashes: Waste ink tank almost full
The printer has a built-in waste ink tank for the ink used during print head cleaning. Eight flashes indicates that the waste ink tank is nearly full. Press the RESUME/CANCEL button to cancel the error so you can continue printing. Before the waste ink tank becomes completely full, contact a Canon service representative.

Note
Canon recommends that you call for service as soon as this error occurs. Once the waste ink tank becomes completely full, printing will no longer be possible.

Sep 14, 2009 | Canon i350 InkJet Printer

1 Answer

Fuel gauge always full


  • Check the floater in the tank may be you need to replace it with a new one.


I’m happy to assist further over the phone at https://www.6ya.com/expert/ramy_d9e7ebea3891f482

Jul 25, 2009 | 2001 Ford Expedition

1 Answer

Ricoh Aficio MP C1500SP - functional error SC202


call ricoh serviceman he/she can fix it.
Defective tank full sensor
• Tank full lever bent or broken
• Incorrect ink suction
1. Check the harness of the tank full sensor.
2. Replace the GJ engine.
3. Replace the maintenance unit.

• The position of the tank full lever
does not stay at the tank full position
after ink initialization or air releasing.
• The position of the tank full lever is
not detected at ink suction.

Aug 19, 2007 | Ricoh Aficio 1515 All-In-One Laser Printer

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Alun Cox

Level 3 Expert

2679 Answers

Brad Brown

Level 3 Expert

18067 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...