PNY OPTIMA 1GB DDR 400 MHz PC3200 Desktop DIMM Memory Module MD1024SD1-400 will this fit my computer?

The Intel® Server Board S875WP1-E supports both ECC and Non ECC Unbuffered PC2100 (266 MHz), PC2700 (333 MHz), or PC3200 (400 MHz) compliant Double Data Rate (DDR) memory modules. Dual channel memory functionality requires two DIMM modules installed into DIMM sockets 1A & 1B, and then DIMM sockets 2A & 2B. The DIMM module size, speed and vendor must be the same.

You can install a single 128 MB memory module into DIMM socket 1A. The minimum supported memory size is 128 MB. The minimum main memory configuration is a single 128 MB memory module, and the maximum configurable memory size is 4GB. With only a single memory module installed, the system will only operate using a one memory channel.
Third party memory vendors may use the same module part number with different
DRAM vendors and die revisions. To insure proper system operation, verify that each DRAM
vendor and die revision has been separately tested and qualified. Please notify CMTL if there is a discrepancy.

Info from the manual:

Memory configurations

You can install 128 MB, 256 MB, 512 MB, and 1GB DDR SDRAM DIMMs into the DIMM sockets using the memory configurations in this section.

• Install only identical (the same type and size) DDR DIMM pairs

using the recommended configurations.

• Make sure that the memory frequency matches the CPU FSB

(Front Side Bus). Refer to the Memory frequency/CPU FSB

synchronization table on the next page.

• This motherboard does not support double-sided 16-bit DDR DIMMs.

• Do not create a three-DIMM configuration in dual-channel mode. The
third DIMM is ignored in the dual-channel operation.

Recommended memory configurations

Memory frequency/CPU FSB synchronization

* Use only identical DDR DIMM pairs.

Sockets

Mode DIMM1 DIMM2 DIMM3 DIMM4

Single-channel (1) Installed - - -

(2) - Installed - -

(3) - - Installed -

(4) - - - Installed

Dual-channel* (1) Installed - Installed -

(2) - Installed - Installed

(3) Installed Installed Installed Installed

CPU FSB DDR DIMM Type Memory Frequency

800 MHz PC3200 400 MHz
533 MHz PC3200/PC2700 400/333 MHz

You should be able to use just 1 stick of 1GB. your model supports
Each memory slot can hold DDR PC2700,DDR PC3200 with a maximum of 1GB per slot.*

Yes. That motherboard can handle a total of 2048 (2 GB) of DDR PC 3200 (AKA DDR 400).

Yes, it will work. Remember that all memory will operate at the speed of the slowest memory though so unless you're completely replacing the memory it won't increase the speed of the memory.

pls check you motherboard manual if it accept that kind of memory because some board cannot accept.

Greetings,

The motherboard will read 1GB DDR400 memory per slot only.

Keep us posted and thank you for using our service.
FixYa for all your troubleshooting needs.

Hi,

the memory you're about to purchase will not work. the maximum gig that the computer can handle per stick is only 1 gig. this system is not designed for 4 gig barrier.

hope this helps.

thanks.

This is from HP.

• Four 184-pin DDR DIMM sockets
• Supports dual channel, eight memory banks DDR 333/400 DDR DIMMs
• Supports 2.5v DDR SDRAM DIMMs
• Maximum HP/Compaq approved memory is 4 GB* without ECC

4 Sticks of PC3200 400 Mhz is max.

RAM has to be

Four 184-pin DDR DIMM sockets

Supports PC3200 (400 MHz) /PC2700 (333 MHz) / PC2100 (266 MHz) DDR DIMM type

Maximum HP/Compaq approved memory module is 1 GB

Maximum HP/Compaq approved memory is 4 GBIt has to be the same.


• If you are replacing a memory module, put the
new memory module in the same memory slot
from which the old memory was removed.
Or
• If you are adding a memory module, install the
new module into the socket nearest the
preinstalled module, and install additional
modules in the next available sockets