Describe your Canon PIXMA MP150 All-In-One

Hi there-
Below are a list of the error codes for this model.
E16-E19 = Failed to scan head alignment sheet.

You can find this information at http://www.usa.canon.com/cusa/home

CANON MP140, MP145, MP150, MP160 RESET ERROR CODES
[Info140] RESET ERROR CODES CANON MP140, MP145, MP150, MP160

E2-2 = No paper (ASF)

E3-3 = Paper jam

E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge
is installed, or the ink cartridges are not installed properly

E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera
Direct Printing

E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16-E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

Hi!
Here is your solution ... to solve you problem follow it....


http://printertools.blogspot.com/2007/10/canon-mp150-reset-codes.html

This just resets the error message - it does not remove excess ink from the waste tank! Good Luck....

To solve your problem please contact this website ...

http://printertools.blogspot.com/2007/10/canon-mp150-reset-codes.html

This just resets the error message - it does not remove excess ink from the waste tank!
Good luck...

Hi

Do you need to reset the counter in MP150?

Anyways remember that you need to repalce the absorbers also later. Follow the below procedure and you can start using the printer again.

PROCEDURE I. Enter Service Mode:

• Plug in power cable
• Hold down STOP/RESET button
• Hold down POWER button
• Release STOP/RESET
• Press STOP/RESET twice in a row

II.Execute Waste Ink Counter Reset Operation:

• Press STOP/RESET button 4 times (Indicator lamp will blink alternately Orange/Green each time the button is pressed)
• Turn off the printer by pressing POWER button (wait until the printer is completely OFF)

When you turn on the printer,waste ink absorber full error is cleared and the printer work normally.

Original source: http://www.printerclinic.com/reset-waste-ink-counter-canon-pixma-mp150/#ixzz1SaAjTfWu

http://www.ziddu.com/download/5724285/ResetCanonMP145.rar.html
download this link

you need to replace the absorber waste ink pad and service the printer

Dear sir your problem is or E8 mean
Waste ink absorber full, or platen waste ink absorber full
follow this step

Hi raj2006678,

The code e23 indicates a paper feed error. Check to be sure that your paper is loaded correctly and that the rollers are functioning properly.

Here is the complete list of error codes for the MP150:
E2 No paper (ASF)
E3 Paper jam
E4 No ink
E5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed
E16 Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

I hope this helps - please let me know if I can be of any further assistance.

Kind regards,
H2H

This is what the manual says: Ink used for cleaning is absorbed in a waste ink absorber placed in the machine. Press [OK] to cancel the error so that you can continue printing. Once the waste ink absorber becomes completely full, printing cannot be done until the waste ink absorber is replaced.
Canon recommends to contact a Canon service representative as soon as possible.

How do I change the ink cartridge for the Canon Pixma 150