eMachines T5224 PC Desktop Logo

Related Topics:

Anonymous
Anonymous Posted on Nov 11, 2010
Answered

I have an emcahine T5224 it was given to me ive tried fixing it and determined its not the HDD because it loads the OS on my other computer and works just fine but for some reason it stops and says there was an issue loading the OS and gives me the options to tr to laod windows normaly, last known working configuration ect. but it still doesnt work, and it is not the HDD because it has been tested and works perfectly, some help please?

Answer This Question
  • Anonymous Nov 11, 2010

    the HDD is from my other computer, just to test it because i didnt not recieve it with any kind of memory, i literaly was just given the computer so dont know much about it, other then no HDD and no ram so had to put my own in, i tried another HDD but i think this HDD that i put in was broken, it came up with Blue Screen STOP: 0x0000007B (OxF8968640, 0xC0000034, 0X00000000, 0x00000000)

×

1 Answer

azzh81

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

  • Expert 74 Answers
  • Posted on Nov 11, 2010
azzh81
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

Joined: Nov 10, 2010
Answers
74
Questions
0
Helped
10878
Points
168

Hi,

You stated that it loads that OS on the other computer. Is this by taking out the hard drive and putting into another PC? If it is, then I would have thought there is h/w issue elsewhere in your PC...

Usually if you have a message saying that it could not load windows properly, it is an OS issue which I would recommend you fix by using your emachines recovery disks.

Hope that helps

  • azzh81 Nov 12, 2010

    If you put in a HDD from your other pc, it will probably have drivers setup that don't work with the Emachine and therefore stop windows from loading. However, if you have a look at the STOP message, it may say something about a memory error. It could therefore also be a RAM issue that causes this error.

    The best thing to do would be to get a blank HDD and check it is detected in the BIOS. Go through the motions of installing Windows - if it fails, chances are that some other hardware has failed. Poss RAM/ Motherboard etc

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My computer has a blue screen error and I tried to install a new O.S but I think it worsens and now I don't know how to fix it
most folks cant, its a computer and are complex.
all are.
no PC stated at all just ATT?
no OS stated windows 10?
first in a shop we test the HDD first or look silly loading say w10 100 times and failing.
most old HDD are dead, or fails smart tests.
wana learn ask.
Read full answer
Jul 08, 2019 • Blue Computers & Internet
0helpful
5answers

I have a external hard drive model HD160U2E-509. It locks up my Computer and i can't retrive any data from it. Can it be repaired without loosing stored data.
It should be. does the computer locks up even when the hard drive is not plugged in
Read full answer
Sep 11, 2008 • Computers & Internet
0helpful
1answer

I cannot get the Dell PowerEdge 840 to recongize and of my HDD in the Raid array.. Trying to install the OS but tells my on HDD is detected
Then you need to get into the BIOS of the PERC RAID controller and inspect the state of the physical/logical volumes. Reboot the machine and watch for the prompt after the PERC5/6 RAID controller loads it's BIOS.

Considering this a null issue given the age, though...
Read full answer
Jan 21, 2014 • Dell PowerEdge 840 (becwmk1_2) Server
0helpful
1answer

I have a dell 9300 that loads bios fine but wont load os even after a complete reinstall? Diag runs threw just fine? it loads to safe mode or normal or bootlog. but then upon entering any option bios...
You might want to play with the BIOS options on the hard drive. If it shows AHCI change it to SCSI then vice versa if the are other options given.
If it still doesn't work, try moving the HDD to a diferent SATA port to check if the OS will load.
If not, it's a possible problem with the HDD.

Let me know what happens next.

Hope this helps!
Read full answer
Aug 07, 2011 • Computers & Internet
0helpful
1answer

When i press the power button my computer turns on and after the dell loading screen it freezes completely if im fast enough i can press F2 F12 and even go to Safe mode screen but none of the options work...
his could be caused by a couple of problems but you are going to need access to a second computer to determine the problem.

1) You have a disk that is failing and it has had an error. Got to the disk makers site and down load their diagnostic program and check the disk. This is a stand alone CD so you don't need to boot into the OS.

Another program that can temporarily fix errors is http://www.dposoft.net/ This program will stop after fixing the first error unless you buy it. Again, this is a stand alone.

If it is a disk error, you need to quickly get your data off and install a new disk.

Don't have a second computer? then you need to take it to a local computer store where they can remove the disk, install it in a desktop and check it for errors.

2) This could be a virus, but I think #1 is your problem. TrendMicro.com has a free online virus scan if you can install the disk in a second computer.
Read full answer
Aug 11, 2010 • Dell Latitude 110L Notebook
0helpful
1answer

Controller MSI K8N Neo4 does not work
SHUT DOWN COMPUTER AND CLEAR CMOS BY RESETTING JUMPER ON MOTHERBOARD AND THEN RETURN JUMPER TO NORMAL POSITION OR USE RESET BUTTON. UNPLUG ALL HDD SATA CONNECTORS FROM HDD. BOOT COMPUTER TO BIOS. MAKE SURE ENABLE ALL SATA IS ENABLED, PRESS F10 AND EXIT.YOU WANT TO SHUT DOWN AGAIN. NOW REATTACH SATA HDD AND CONNECTORS AND BOOT TO BIOS AGAIN. NOW HIT F10 AND LET COMPUTER RESTART AND LOAD INTO THE OS. LOGON AND CHECK DEVICE MANAGER..SHOULD BE THERE. IF NOT CHECK MOTHER BOARD WEB SITE FOR BIOS UPDATE. IF BIOS UPDATE DOESN'T DO THE TRICK, SHUT DOWN AND DISCONNECT THE IDE DRIVE, UNLESS IT CONTAINS YOUR OS. TRY BOOTING TO BIOS AND CHANGE ORDER OF 1ST BOOT OPTIONS, HIT F10 AND EXIT AND ALLOW COMPUTER TO BOOT TO OS, THEN LOGON, GO TO DEVICE MANAGER AND REMOVE IDE AND RESTART, ONLY IF THIS HDD DOES NOT CONTAIN OS. YOU SHOULD BE FINE AFTER THIS, OR INSTALL YOUR OS ON THE SATA HDD.
Read full answer
Apr 09, 2010 • MSI K8N Neo4 Platinum nForce4 ultra K8...
1helpful
1answer

I have a Maxtor one touch 2 external hard drive,serial#2dd10020,worked fine on Windows XP,I'am now using it on Windows 7,it shows up in computer as drive Z,I cannot unlock it to get to my files,any help...
ok for one your computer no matter what OS you are using stores no drive letter , a drive letter is only given in the order as it is
installed on your system for example if you use 2 internal HDD
and one external HDD your computers C: drive will be the master
the F: will be the slave and the external will be G: , now if you have changed the order of the drives from your last OS then it
will conflict to the last drive letter given , your unit will know
what letter it was given so it must be in the same location for
the new OS , there is also the possibility that Windows 7 doesn't
support the driver for that unit , you can try hooking it up to
another computer retrieving your data , then hooking it back
up to windows 7 run its software , then installing the data back
into your HDD
Read full answer
Jan 29, 2010 • Maxtor OneTouch II external hard drive...
0helpful
1answer

My acer 5630 laptop does not boot up
Try reinstalling the OS with your restore disks. It might be that you have HDD failure in which case you would need to replace the HDD.
Read full answer
Feb 01, 2009 • Acer Aspire 5600 Series 5630-6951 Laptop
0helpful
2answers

Wont load
It is on your os problem. Insert your OS installer. You don't have to install a fresh copy but you can repair your previous OS installation. Make sure you have set your boot sequence to CD, floppy and last HDD. You can now reinstall your drivers after doing that.
Read full answer
Dec 21, 2008 • Acer Aspire SA80 (ASA80UC4603) PC Desktop
Not finding what you are looking for?

View Most Popular

T5224 PC Desktop

  • Computers & Internet

Related Question

My computer has a blue screen error and I tried to install a new O.S but I think it worsens and now I don't know how to fix it

  • Blue Computers & Internet

Related Topics

330 views

Ask a Question

Usually answered in minutes!

Popular Questions

Multimedia audio controller driver problem

eMachines T6534 PC Desktop

Optiarc DVD RW AD-7561A This device cannot start. (Code 10)

eMachines T5274 Desktop PC

Optiarc dvd rw ad-7561a ata device

eMachines T5274 Desktop PC

My cpu fan will not shut off it is so loud should

eMachines T5048 PC Desktop

TRYING TO HOOK UP MU POWER BUTTON NEED TO KNOW

eMachines T6420 PC Desktop

Check Out the Mobile Browsers Report
Check Out the Mobile Browsers Report

View all Fixya Reports

Top eMachines Computers & Internet Experts

Andrew Chrostek
Andrew Chrostek

Level 1 Expert

187 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you an eMachines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...