Reset Power I have a Hp All-In-One Printer 5610. This is New Printer. I Have problem in this printer It shows on printer display reset power.

An '0x ...' Error Message Displays on the Front Panel When Printing HP Photosmart C5380 All-in-One Printer - HP Customer Care (United States - English)

Hello
HP suggests 3 reset levels.
Power off printer, then press and hold buttons while powering on, if it doesnn't reset, then unplug it and press and hold buttons while plugging it in,
# and 3 Partial Reset
# and 6 Semi-Full Reset
# and 9 Full Reset
A Full Reset will clear any stored information in the printer, speed dials, etc, so always start with a partial reset and work your way up.
Hope this helps

You need to reset the printer

Follow the steps :

1. Unplug the power cord from the back of the printer while the printer is on

2. Press # and 6 button at the same time.

3. While holding them plug in the power cord

4. You will see a message on the printer Semi Full Reset - Release the buttons

Note : While doing it you will lose all the numbers which you have saved in your printer

Hi,

Its time to reset the printer; follow the below steps

Power Drain:

• Turn OFF the printer, disconnect the power cable from backside of the printer and from wall outlet.
• Press and hold the Power button for 60 seconds.
• Connect the cable and turn ON the printer.

Partial Reset

• Remove the power cable from back side of the printer while its ON.
• Press and hold "#" and "3" button, while holding them both insert the power cable and release the button after 10 seconds.
• If printer turns OFF, press power button to turn it ON.

Semi-Full reset

• Remove the ink cartridges.
• Remove the power cable from back side of the printer while its ON.
• Press and hold "#" and "6" button, while holding them both insert the power cable and release the button after 10 seconds.
• If printer turns OFF, press power button to turn it ON.
• Insert the ink cartridges.

NVM Reset

• Remove the ink cartridges.
• Remove the power cable from back side of the printer while its ON.
• Press and hold "OK" and "Cancel" button, while holding them both insert the power cable and release the button after 10 seconds.
• If printer turns OFF, press power button to turn it ON.
• Insert the ink cartridges.

Regards
Riztech

unplug it from the computer and unplug it from the wall socket and hold the power button down for 60 seconds then replug it back in to the computer and plug the power back on then turn it on.

you can try a reset on your printer.
follow the below steps to reset.
Reset the All-in-One to the factory default settings by using these instructions:

1. Unplug the power cable from printer when the printer is powered on and wait for 20 seconds.

2. Then, press and hold # and 6 while plugging in the power cord.

Continue holding until it displays Semi Full Reset message in the front panel of the All-in-One.

This document should help you out. Follow the instructions carefully.

An '0x ...' Error Message Displays on the Front Panel When Printing

Unplug the power cord from the All-In-One as well as the power outlet.
Plug the power cord directly to a wall outlet without surg protector. (if possible connect it to a different power outlet)
Before connecting the power cord to the All-In-One press and hold the # and no 6 button and then insert the power cord, do not release the keys until you see a message a reset (if the screen goes blank then release the keys and turn the power on)
Then check and see

Good Luck

You can try resetting the printer.
Step 1. Unplug the power cord at the back of the printer while the printer is still on
Step 2. Press and hold the # and 6 button on the printer while the power cord is disconnected. And keep holdig the two buttons until you plug in the power back again.
Note : do not release the # and 6 when you plug the power cord back in. keep holding the two buttons until the printer would turn on then turn off or the printer would say anything about "reset"
Step 3. Try sending a fax after the successful reset of the printer

UNPLUG PRINTER FROM WALL SOCKET PRESS # AND 9 AS YOU PLUG PRINTER BACK IN TO DO A FULL RESET