Lcd folding unit - JVC Everio GZ-MG130 Camcorder

Are you using the remote? Replace the battery in it. Will it fold using the buttons on the unit? Additional 'child safe' buttons for folding & unfolding are located just under the drive controls, just in case you should misplace or lose your personal wireless remote.

https://www.google.com/search?q=kymco+k-lite+fe+not+folding

..

It should not be too difficult to disconnect the LCD screen from the "foot" unit. The resulting two pieces will be "flatter" and will be better-suited for packaging.

Hi David

At the moment the Quinny Zapp Xtra with folding seat unit is only available in the USA.

If you are in the USA please contact [email protected] to ask them about compatibility between the products you have and the new Quinny Zapp Xtra folding seat unit.

If you are not in the USA we must advise you not to attempt to combine your products with a USA Quinny Zapp Xtra folding seat unit as the products have not been tested or approved in combination.

There may your LCD connecting flip is defective, just replace it and camera will be fine.

Baby Jogger's patented Quick-Fold Technology, this stroller is the only in-line stroller to fold flat in one simple step. Just pull the clearly marked "FOLD" handle and the stroller or jogger collapses into an easily loadable and storable unit. This is quite possibly the easiest fold on the market today.

You can buy a new LCD from eBay. The problem is cause by the backlight cable breaking because Delphi folds it behind the LCD in manufacturing. If you know how to solder, you can solder a wire in place of the broken flat cable to fix it.

jorickfranke, A picture is worth a thousand words!! Or in your case, a "video clip" at YOUTUBE! ! ! Search This "lcd monitor disassembly" or "lcd monitor repair" I'm sure you will find out how to do it. Just don't use sharp cutting instruments for "parting" the rear cover from the "front bezel" of unit. Cost of repair increases 10 fold if trip to hospital "ER" is required.
Good luck. 12fixlouie

You have gas shocks on each side of the unit need to see if they are dry and causing the unit not to fully fold down use a little machine oil on the rods this should take of it if not, either the shock are defective or some how you manage to fold the unit when the incline was not at its minimum.
1) engage key the look at incline display needs to be either 0 or 1 degree 2) if shock are defective replace shocks. Hope this help!!

When the big LCD is black the view finder will turn on, right?
You need to replace a new hinge unit. Here is similar solution
How to fix an intermittent display LCD on Canon PowerShot S5IS

For clarification: You turn on your unit, the blue magellan logo appears clearly, but then the screen slowly starts turning white. Turning the unit off/on fixes the white but images are in reverse. CAUTION: It would help if you were grounded in some way prior to proceeding. Also, of course do this at your own risk. Make sure the cable going from the main board to the LCD is making a solid connection: 1. Take screws out of rear housing 2. Slightly seperate the rear/front housing 3. Disconnect the RF cable attached on the corner of the main board. 4. Pull off (or locate if they already fell off) 4 O rings from the screw mounts. 5. Fold over mainboard ontop of rear housing 6. Use fingernail or tweezers to lift up the plastic locking mechanism that attaches your LCD to the backside of your mainboard. 7. Pull out LCD cable, inspect for "gunk" on conacts (clean if necessary) 8. Shove cable back into slot on mainboard 9. Press down locking mechanism 10. fold mainboard back over 11. Put 4 O rings back on screw mounts 12. PLUG RF CABLE BACK IN! (signal will be zero if this doesn't happen) 13. Fit together front/back and screw back in.