Can not set top-of-form position. Instructions are followed as in guide, "Hold pause, adjust with the micro-adjust, pause again to save." And It is still not dropping the paper down from the tear off point tp print at the top of the page. It just starts printing at the tear off which is right in the missle of the page.

1. Push the ALT button and then the PARK LOAD button to back the paper out.
   
2. Push the PARK LOAD button to reload the paper. The Ready light should now be blinking.
   
3. Use the MICRO up or down buttons to adjust as needed, making sure that the top of form is set on the very first page that enters the printer. Typically, the top edge of the first sheet of paper should be even with the ribbon.
   
4. When the page is lined up properly, press the START/STOP button. The printer will record the current position as the top of form and then feed paper to the tear off position.
   
5. Use the MICRO up and down buttons to place the top of the paper at the tear off bar.
   
6. After the tear off is positioned properly, press the START/STOP button twice to save the tear off position.
   
7. Test the positions with a sample print job. If the alignment is still off, follow this entire procedure from the beginning again as needed.

Hi,
Please get the compatible driver here :
www.driverskit.com/MP3.html
www.nodevice.com/driver/category/MP3_Player.html
www.freedownloadscenter.com/Best/free-mp3-driver.html
www.driverslab.com/drivers/MP3/iRiver/15/56.html
www.samsung.com/us/support/downloads
Warm regards, Jay__Kuh73

Hi,
Please get the compatible driver here :
www.driverskit.com/MP3.html
www.nodevice.com/driver/category/MP3_Player.html
www.freedownloadscenter.com/Best/free-mp3-driver.html
www.driverslab.com/drivers/MP3/iRiver/15/56.html
www.samsung.com/us/support/downloads
Warm regards, Jay__90Jh7

Make sure continuous forms are in the printer.
Press Alt and then press Setup to enter Setup Mode.The
printer prints out the Main Menu.
To select a function, press the buttons listed on the printout.
To save the setting and leave Setup Mode, press Start/Stop
until out of the menu.

There are several way that may adjust the Panasonic phone clock, please try the following suggestion method:

Method 1:
1) Press PROG soft button, follow by HOLD button.
2) LCD show direct the time adjust, key in the correct time, let's say 8.15am, so key in 815 and press STORE.
3) Press END or HOLD to end the setting.

Method 2:
1) Press PROG soft button, follow by HOLD button, follow by # button.
2) LCD show time adjust, key in the correct time, let's say 8.15am, so key in 815 and press STORE.
3) Press again # button to select between AM and PM mode.
4) Press again STORE to save the setting.
5) Press END or HOLD to end the setting.

Method 3:
1) Press PROG button, follow by key * * 1 2 3 4.
2) Press key 0 0 0 to display the day/time setting.
3) Press |> or SP-PHONE button if u wish to change the date.
4) Press |> or SP-PHONE button to change the time.
5) Press CLEAR or TRANSFER button to change current hour entry.
6) Press |> or FWD/DND button to change current minutes entry.
7) Press |> or FWD/DND button again and AUTO ANS button to change between AM or PM.
8) Press STORE to save the setting.
9) Press END or HOLD to end the setting.

Hope these help.

YBC (/\)

There is no easy way. You need to adjust starting position for every form. There is fine feed function and Top Of Form setting procedure, so you can adjust the minimum space between top of porm and first printed string (user's guide explains in details how to do it). But after that you need to decide whether you manually set the start position by rotating the knob or play with your application to adjust margins etc.

aprendizaje hablar español :)

1. Make sure the printer is turned on and the desired tractor is selected (the corresponding tractor arrow should be lit).
2. Open the upper cover.
3. Press the Top of Form button to enter top-of-form mode. The printer beeps once, and the Top of Form light turns on.
4. Use the Micro Feed buttons to feed the paper to the desired top-of-form position. The “A” on the ribbon protector shows you where the bottom edge of your first line of text will print. This position is based on the first printable line of text. If your software inserts a top margin of five lines, your text will actually print five lines below the top-of-form position.
5. Press the Top of Form button again to exit and save your new top-of-form position. Then close the top cover.

***
No he intentado traducir las instrucciones mientras que puede causar la confusión.

The book says:
Besure auto ret. is off.
Hold forms key an press form # 01- 99, app light goes on and forms light blinks.
Inset form at 0 paper scale position. Pull paper bail forward form will load to the first marked position.
Type info and then phrase T/W will move to the next marked position.

The full instructions are about 4 pages long, if you have a fax # I can send them to you

DockyO

Hi-

When you said line feed do you mean the Top of form?

hope this helps

1. Make sure the printer is turned on and the desired tractor is selected (the corresponding tractor arrow should be lit).
2. Open the upper cover.
3. Press the Top of Form button to enter top-of-form mode. The printer beeps once, and the Top of Form light turns on.
4. Use the Micro Feed buttons to feed the paper to the desired top-of-form position. The “A” on the ribbon protector shows you where the bottom edge of your first line of text will print. This position is based on the first printable line of text. If your software inserts a top margin of five lines, your text will actually print five lines below the top-of-form position.
5. Press the Top of Form button again to exit and save your new top-of-form position. Then close the top cover.

Keep me posted if you have inquiries, thanks!

Please try the following to resolved that issue:

1. Make sure the printer is turned on and the desired tractor is selected (the corresponding tractor arrow should be lit).
2. Open the upper cover.
3. Press the Top of Form button to enter top-of-form mode. The printer beeps once, and the Top of Form light turns on.
4. Use the Micro Feed buttons to feed the paper to the desired top-of-form position. The “A” on the ribbon protector shows you where the bottom edge of your first line of text will print. This position is based on the first printable line of text. If your software inserts a top margin of five lines, your text will actually print five lines below the top-of-form position.
5. Press the Top of Form button again to exit and save your new top-of-form position. Then close the top cover.