Whirlpool Duet Steam WFW9700V Front Load Washer / Dryer Logo
Posted on Oct 16, 2010
Answered

Cycle stops and F35 displays flashing - Whirlpool Duet Steam WFW9700V Front Load Washer / Dryer

Answer This Question

1 Answer

jayadams4

jayadams4

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Apr 07, 2012
jayadams4
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.

Joined: Apr 07, 2012
Answers
1
Questions
0
Helped
100
Points
2

I blew mine out with compressed air and it worked, You have to take the cover off and remove the small rubber hose. Then blow out the hose and blow into the small hole on the sensor. It is easy to remove from the machine, 3 screws in the back then remove the rubber hose, twist the unit so the bottom is facing the back of the washer and it pops right out, then remove the wire plug.

  • jayadams4
    jayadams4 Apr 07, 2012

    I blew mine out with compressed air and it worked, You have to take the cover off and remove the small rubber hose. Then blow out the hose and blow into the small hole on the sensor. It is easy to remove from the machine, 3 screws in the back then remove the rubber hose, twist the unit so the bottom is facing the back of the washer and it pops right out, then remove the wire plug.

  • jayadams4
    jayadams4 May 04, 2014

    But it only worked for a few days, ended up replacing it!

×

3 Related Answers

Anonymous

  • 530 Answers
  • Posted on Jun 25, 2009

SOURCE: F35 flashing

if it is less than one year old call for service it should be covered. if not take the kick panel off and locate the tech sheet it is either in the kick panel or in the cabinet to the right. it will give you a list of error codes find out what it means and let me know thanks

Ad

Oloyede Monsuru

  • 1468 Answers
  • Posted on Jun 03, 2010

SOURCE: Code F35

hello
what The F35 error code indicates that the water temperature sensor reading is out of range (below 23 degrees F or above 217 degrees F)
The f35 error shows you and indication that ice maker sensor readings are out of normal range.
then what you need to do to fix up the problem is to bale out the water from it then clean up all form of water ant dry you can see from the screen

Please before you can carry out this instruction you will have to put OFF all source of power supply .

thank you and good luck.

Anonymous

  • 1998 Answers
  • Posted on Mar 22, 2011

SOURCE: In some cycles the word

one of our techs has already answered this on the f35 error code click here http://www.fixya.com/support/t400054-error_code if you have any further questions message me back and please remember to rank how this opinion has helped it allows me to help others in the future Thanks Rick
p.s to repair this issue you would replace the analog pressure switch the switch's part number is W10156252

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

May tag 5000. f35 what does that mean
"F35" means Analog Pressure Sensor Failure

If the washer does not accept inputs from the control panel, follow the Hard Reset steps below to reset the control:
Unplug or turn the circuit breaker off for 30 seconds.
Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.
Press the Pause / Cancel / Stop button twice to clear the display.
Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.

Note: If the Hard Reset does not work, there may be an internal failure with the washer, that requires service.

Hope this helps.
Read full answer
Jul 09, 2011 • Maytag Washing Machines
2helpful
1answer

In some cycles the word sud appears on the display. Then the cycle will stop and F35 appears on the display.
one of our techs has already answered this on the f35 error code click here http://www.fixya.com/support/t400054-error_code if you have any further questions message me back and please remember to rank how this opinion has helped it allows me to help others in the future Thanks Rick
p.s to repair this issue you would replace the analog pressure switch the switch's part number is W10156252
Read full answer
Mar 22, 2011 • Whirlpool Duet GHW9150P Front Load Washer
1helpful
1answer

Code F35
hello
what The F35 error code indicates that the water temperature sensor reading is out of range (below 23 degrees F or above 217 degrees F)
The f35 error shows you and indication that ice maker sensor readings are out of normal range.
then what you need to do to fix up the problem is to bale out the water from it then clean up all form of water ant dry you can see from the screen

Please before you can carry out this instruction you will have to put OFF all source of power supply .

thank you and good luck.
Read full answer
Jun 03, 2010 • Whirlpool Duet GHW9150P Front Load Washer
2helpful
1answer

Code F35 on Kenmore Elite HE5t front loader washer.
F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.%^#$
Read full answer
Apr 09, 2010 • Kenmore Elite 45986 Front Load Washer
2helpful
3answers

Whirlpool Duet -Sud displays and washer stops
I;ve had the same problem (SUD on first fill) and found this most helpful for my WFW9600TW01 Duet washer

http://www.tellingmachine.com/post/Fixing-Sud-and-F35-errors-on-my-Whirlpool-WFW9600TW01-Washer.aspx

I duplicated his actions and it cleared up my SUD/F35 error. I think running the diagnostic test multiple times flushes the sensors/sensing lines to eliminate the problem.
Read full answer
Jan 30, 2010 • Whirlpool Duet GHW9150P Front Load Washer
3helpful
1answer

Kenmore Elite front load washer stops and blinks F35 and locks up
f35 code indicates a pressure switch problem. Try unplugging unit for 2 minutes.Plug back in and test.If F35 reappears,check hose from tub to pressure switch
Read full answer
Nov 04, 2009 • Kenmore Elite 45986 Front Load Washer
1helpful
3answers

F35 message, will not run through cycle. Starts to and then the F35 starts flashing and eventually shuts off.
Check between door boot seal and drain hose in basket. If this is clogged with lint or sock, towel it will code f35 or sud
Read full answer
Oct 22, 2009 • Whirlpool Duet GHW9150P Front Load Washer
4helpful
1answer

My Kenmore Elite HE5t washer flashes SUD continually, then goes to F35 mode and shuts off. Help!
Sometimes the SUDS/F35 is because of TOO MUCH detergent. To clear you have to set the cycle on rinse and then keep pouring cups of water into the detergent container as the cycle is going. You might have to do this a few times because if the SUDS message comes up the water flow will stop. Just unplug and try again. Also when the detergent container is finally clear you will see the little rotators gears move around when the cycle starts.
Read full answer
Aug 02, 2009 • Kenmore Washing Machines
4helpful
1answer

Error code F35
F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
Read full answer
May 18, 2009 • Kenmore HE2 Plus Front Load Washer
5helpful
1answer

Sears Kenmore HE3 Error Code F35
F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
Read full answer
Aug 25, 2008 • Kenmore Elite 45986 Front Load Washer
Not finding what you are looking for?

View Most Popular

Duet Steam WFW9700V Front Load Washer / Dryer

  • Washing Machines

Related Question

May tag 5000. f35 what does that mean

  • Maytag Washing Machines

Related Topics

110 views

Ask a Question

Usually answered in minutes!

Popular Questions

Whirlpool Duet Sport Washer will not drain - F-21 error

Whirlpool Duet GHW9150P Front Load...

F 11 error code on Whirlpool Duet - Serial Communication Error ?

Whirlpool Duet GHW9150P Front Load...

Whirlpool Duet Washer-error code "sud"

Whirlpool Duet GHW9150P Front Load...

Whirlpool duet washer-error F06 and E02

Whirlpool Duet Steam WFW9750WR...

ERROR CODE (F24) ON A WHIRLPOOL FRONT LOAD WASHER

Whirlpool Duet GHW9150P Front Load...

Top Whirlpool Washing Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...