MODEL # ZD4200DO2BB IT WOULD NOT DRAIN ON THE WASH CYCLE THE WATER AND FOAM COME OUR FROM THE FRONT WHAT CAN I DO?

you need to unblock the pipe work from the tub to the pump ,,then the pump,, and the pipe from the pump to the drain

6 - 1
DIAGNOSIS & TROUBLESHOOTING
SUDS DETECTION
During Drain Routine
During the Drain Routine, the water level is checked continuously. Normal drain will occur until the
pressure switch senses no water in the wash tub and there is no foam (suds). The drain pump will
operate an additional 15 seconds after the pressure switch reports no water or foam.
If the drain routine operates for four (4) minutes and the pressure switch senses any foam (suds) in
the wash tub, the Central Control Unit will start the "Kill-Foam" Routine. (See description of this
Routine below.) After the Kill-foam Routine is concluded, the Drain Routine will restart. If, after
four (4) minutes the pressure switch still senses foam in the wash tub, the Central Control Unit will
go into Failure Mode. The digital display will show, F02.
During Spin (Extract) Routine
During the Spin/Extract Routine the water level is checked continuously. If, during this routine, the
pressure switch senses the presence of foam (suds) in the wash tub, the Central Control Unit will
stop the drive motor and the basket will stop spinning. The electronic control will count the number
of spin repetitions that are attempted due to foam (suds). There are a maximum of three (3)
attempts for each Spin/Extract Routine.
Kill-Foam Routine
1.
The Remaining Time counter is stopped.
2.
The digital display shows Sud.
3.
The Drain Pump is turned OFF.
4.
The Central Control Unit will fill the wash tub with 1 gal. (4 L) of cold water.
5.
While the tub is filling the basket will tumble 1 sec. ON/15 Sec. OFF.
6.
Once the tub is filled, the drive motor will turn OFF and the basket will rest without any
movement for five (5) minutes.
7.
After the five (5) minute rest, the remaining time counter will restart and the digital display
will show the remaining time left in the routine.
NOTE:
If the Kill-Foam routine was initiated during a Spin/Extract Routine, the tumbling action
will be reduced to a cycle of 3 sec. ON/13 sec. OFF. If, at the end of either the Drain or Spin/
Extract Routines, a suds condition still remains, the digital display will show Sud.
Sud will also be displayed for a short period at the end of a cycle, if a Suds condition was
detected during the cycle. This will alert the consumer to reduce the amount of detergent in
subsequent uses MANUAL

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

sound like wash heater failure if it doesnt reach wash temp it will jump back to beginning of heat phase,thats why you get a lot of foam heat will suppress this as part of the wash action.

Hello,
After you the drain to discharge the remain water and the tub is visibly dry of water,then you open and load it do you see standing water after you have drained and know it was gone??
If that is the case what i believe your trouble is that where the dishwasher drain connects to disposer under the sink the drain hose is only leading from that nozzle downward,if that is so what is happening is the dishwasher is draining ok but backfilling whenever water runs through the sink. To fix that use a string on plastic zip tie and attach a portio of the drain hose so at one point the drain hose under the sink is higher that the nozzle and water in the sink will longer run into the hose and run upward since water is only going to drain down and wont ever rise on its own.The drain pump is powerful enough to push the drain water up that "HIGHLOOP" very easily.

Good luck i hope this has helped you to fix your dishwasher,
Gene

SUDS DETECTION

During Drain Routine

During the Drain Routine, the water level is checked continuously. Normal drain will occur until the

pressure switch senses no water in the wash tub and there is no foam (suds). The drain pump will

operate an additional 15 seconds after the pressure switch reports no water or foam.

If the drain routine operates for four (4) minutes and the pressure switch senses any foam (suds) in

the wash tub, the Central Control Unit will start the "Kill-Foam" Routine. (See description of this

Routine below.) After the Kill-foam Routine is concluded, the Drain Routine will restart. If, after

four (4) minutes the pressure switch still senses foam in the wash tub, the Central Control Unit will

go into Failure Mode. The digital display will show, F02.

During Spin (Extract) Routine

During the Spin/Extract Routine the water level is checked continuously. If, during this routine, the

pressure switch senses the presence of foam (suds) in the wash tub, the Central Control Unit will

stop the drive motor and the basket will stop spinning. The electronic control will count the number

of spin repetitions that are attempted due to foam (suds). There are a maximum of three (3)

attempts for each Spin/Extract Routine.

Kill-Foam Routine

1. The Remaining Time counter is stopped.

2. The digital display shows Sud.

3. The Drain Pump is turned OFF.

4. The Central Control Unit will fill the wash tub with 1 gal. (4 L) of cold water.

5. While the tub is filling the basket will tumble 1 sec. ON/15 Sec. OFF.

6. Once the tub is filled, the drive motor will turn OFF and the basket will rest without any

movement for five (5) minutes.

7. After the five (5) minute rest, the remaining time counter will restart and the digital display

will show the remaining time left in the routine.

NOTE: If the Kill-Foam routine was initiated during a Spin/Extract Routine, the tumbling action

will be reduced to a cycle of 3 sec. ON/13 sec. OFF. If, at the end of either the Drain or Spin/

Extract Routines, a suds condition still remains, the digital display will show Sud.

Sud will also be displayed for a short period at the end of a cycle, if a Suds condition was

detected during the cycle. This will alert the consumer to reduce the amount of detergent in
subsequent uses.

the drain pump is not working,after wash cycle the washer should drain the used water,if it does not function-all the next cycle will not commence.

drain hose could be plugged.

check out another website. ths.gardenweb.com/forum/laundry for other fix it tips on FPaykel.

My Frigidaire front loader washer model LTF2140E doesnt want to drain the water when set to wash (heavy-normal-quick selectors). It washes put thats it. I have to switch the selector to drain/spin then rinse/spin cycle to finish the load. I checked the drain hose for any clogs....everything is clear. Any suggestions? Also,iIs their any reset buttons for this type of washer?

something is stuck in the drain pump axcess through front panel.