At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: The electrical cord seems to have come loose near the...
This has been happening since the first cord was attached to the first electric iron. The cord takes a beating. You will have to disassemble the handle and fix it ... or get a replacement.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There are a few possible causes for your Tefal iron cutting out after about 10 minutes of use:
Overheating: The iron may be overheating and shutting off as a safety measure. This could be caused by a clogged steam vent or a malfunctioning heating element.
Electrical issues: The iron may be experiencing electrical issues, such as a faulty power cord or a problem with the outlet.
Water leaks: If the iron is leaking water, it could be causing the iron to shut off. Check for any visible leaks and make sure the water tank is properly sealed.
Malfunctioning thermostat: The iron's thermostat may be malfunctioning, causing it to shut off unexpectedly.
sounds like a loose connection in the power transfer, some piece of metal may be broken or the cord itself may be damaged in some place, you could try replacing the cord. I would just go and buy a new iron. They aren't all that expensive anymore. Good luck with whatever you decide to do. I hope you solve your problem. If you want any further help or have any other questions, please let me know, otherwise have a Good Day.
Check the cord for any kinks or cuts before checking the cord connection to the appliance itself for loose or touching wires. What is decalc the iron ?
see the causes and proceed according, fix it. God bless you If the iron doesn't heat, make sure power is on to the outlet, check the electrical cord, and check the thermostat (see the Appliance Controls Fix-It Guide) and replace if necessary.
If the iron heats but steams improperly, inspect the soleplate and
clean the vents (see below) and flush sediment out of the steam chamber
(see below).
If the iron produces too much or too little heat, test the electrical cord. Also test and, if needed, adjust calibration of the thermostat (see the Appliance Controls Fix-It Guide).
see the causes and proceed according. fix it. God bless you If the iron doesn't heat, make sure power is on to the outlet, check the electrical cord, and check the thermostat (see the Appliance Controls Fix-It Guide) and replace if necessary.
If the iron heats but steams improperly, inspect the soleplate and
clean the vents (see below) and flush sediment out of the steam chamber
(see below).
If the iron produces too much or too little heat, test the electrical cord. Also test and, if needed, adjust calibration of the thermostat (see the Appliance Controls Fix-It Guide).
Hi!!
It should be an access plate fasten by a couple of screws right below the power cord, remove them and fix the cord's terminals/contacts or the cord itself.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.
If the iron is still in warranty send it back via the shop where you bought it, the inner wire is frayed and needs replacement, if you know an electrician its as simple as shortening the flex by a few inches and reattaching it again. the inner wires twist with time and become frayed or come loose from connection
Try re-tightening the wires at the plug and on the iron, but if this does not solve the problem ,replace the cable.You should be able to get it from your local hardware.
Hope this has helped you
Please come back to me if you have any further issues
"FF" or a blinking light will display meaning “Fault Found”. The “fault” is in the amount of power available to the blanket, mattress pad or throw.
There are several causes to this problem: 1. Bedding product is plugged into an extension cord, surge protector, power strip, or not plugged into a direct wall outlet. 2. Bedding product wasn't plugged in properly.
To FIX this problem, do the following to reset your bedding product:
1. Unplug the power cord from the electrical connection. 2. Unplug the cord from the actual bedding product itself. 3. Re-plug the cord into the bedding product. Make sure the connection is secure and complete. 4. Re-insert power cord back into a wall outlet.
If the 4 steps above are not followed in order, the bedding product will not properly reset.
×