GE 29488 My line 1 is inactive and the error message says that it is inhibited. My line 1 in-use button changes from red to greenish and intermittantly says that it is in use. I cannot transfer to this line or speakerphone this line and the calls are not ringing in. Help! Chris

1. VR2/VSI DIAGNOSTIC FLASH CODES

# OF LEDS
CODE
CAUSE
POSSIBLE SOLUTION
One red LED
1
Low battery voltage
Charge batteries
Two red LEDs
2
Left motor open
Make sure left motor is plugged into controller.
Three red LEDs
3
Left motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs One yellow LED
4
Right motor open
Make sure right motor is plugged into controller.
Three red LEDs Two yellow LEDs
5
Right motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs Three yellow LEDs
6
Inhibit active
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs
7
Joystick error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs One green LED
8
Controller error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs Two green LEDs
9
Brake fault
Make sure both motors are plugged into controller.
Three red LEDs Four yellow LEDs Three green LEDs
10
High battery voltage
Contact your authorized Pride Provider.
What if the speed LEDs on the VR2/VSI begin to flash?

• Determine if the battery charger is connected to the power base. When the battery charger is connected to the power base, a charger inhibit feature keeps the power chair from driving. This is indicated by the VR2/VSI speed
  LED(s) flashing.
• Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to
  activate.
• Determine if all controller connections are plugged into the power base properly. If the 3-pin charger
  inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

Hi. Inactive feature often means that there's a problem with your connection to the call pilot. Do you have lights on your call pilot? Did you assign a mailbox to the extension you're working on? Did you remember to connect the call pilot to a station port?

From left to right:
(Lights)
Exclamation point: Error
Weird Monitor beat symbol: Jam
Paper: Out of paper
Toner (Triangle leading down to dot pyramid): Toner refill
Lightbulb: ready

(buttons)
Greenish Play button (square with triangle): Continue
Red button with x: Stop/Cancel
Dell 2230 User Guide Page 1

Hello and Welcome to FixYa!
Inactive SIM message may arise due to more than one issues. First things first check the hardware of your phone, to do this Put out the SIM card and check what happens. If it shows insert SIM card, its normal. If it shows the same inactive message then hardware malfunctioning.
Ok if the hardware is ok, then its simple. Inactive SIM means that your SIM card is not being able to register your Network carrier. The Phone with a red-line means SIM card registration failed. Although the signal radar works. This may be due to 2 issue; either there is a issue at the Service provider End, to check this call the service providers from other cell or land-line and check the status of your connection against this SIM Card No. If they say everything is ok. Then Its confirmed that your Phone is Network locked (Can only be used for one specific network) In this case coordinate with the seller.
I hope you will have a clearer picture now.

If you have any Confusion, questions or issues regarding your problem do tell me.
Thank you for using FixYa!, Keep visiting..
If you think I was of help, your token of appreciation in the form of rating and a testimonial will be esteemed.
Concerned, Nooh

Have you tried using 7 to delete messages or are you afraid you'll mess something else. 7 is the universal delete number. Try it, maybe leave yourself a message and use it as the guinea pig.
Alternately, does your handset have a button with an X on it and the word "delete" or "clear"? If so that is delete key and pressing it once deletes the one message and pressing it a second time will delete them all,

If you have more than one phone then its probably flashing because the phone ID is the same as another phone on your system or not setup up yet with an ID just has two dashes (--). or you if you have more than one phone on the system and have more than 2 lines coming into the phone, they all have to be on line 1 together in the first port on the back. Communication between sets are done on line 1

problem for lipi 6312 tally genicom line printer my printer shows an error (hammer voltage 1)

hitachi model 51f510 projection tv has horizontal lines & has greenish tint,do i need to chang the bulbs??i alredy tryd the magic focus button & manual focus,but unsuccesfl,any ideas????

http://phone.manualsonline.com/ex/thread/view/idThread/1810597


http://www.retrevo.com/s/GE-25414RE3-Telephones-review-manual/id/2877ag907/t/1-2/

unplug the phone, remove any batteries, and unplug the phone cord, wait ten minutes, and replace batteries, plug it back in and it should reset it.