Lost the directions need to know how to set all the buttons

Model 40018: You do not need the 9-volt battery to operate this clock.
NO TIME DISPLAYED WHEN PLUGGED INTO AC POWER:
If the display is blank when plugged into the AC outlet, unplug from AC power and remove the Insta-Set battery (lithium button cell), then plug into AC power again and manually set the Time and Date.

• HOUR: Press and hold the DST SET button for 7 seconds until the 12:00 flashes. Use the PLUS and MINUS buttons to set the Hour. Press and release the DST button to move to the Minutes.
• MINUTES: The Minutes will be flashing. Use the PLUS and MINUS buttons to set the Minutes. Press and release the DST SET button to move to the Month.
• MONTH:The Month will be flashing. Use the PLUS and MINUS buttons to set the Month. Press and release the DST SET button to move to the Date.
• DATE: TheDate will be flashing. Use the PLUS and MINUS buttons to set the Date. Press and release the DST SET button to move to the Year.
• YEAR: The Minutes will be flashing. Use the PLUS and MINUS buttons to set the Year. Press and release the DST SET button to secure the setting in the memory.

After completing the manual set for time and date, insert a fresh Insta-Set button cell battery and the settings will automatically be stored in the clock.

hello, I enclose you a link to a website containing universal codes, which attempt to find the appropriate code to your TV model. Try the first option of direct income by type of TV code. If that fails, try the automatic scan. Good luck! Let me know if you need additional guidance.

http://kbase.x10.com/wiki/Four_Digit_Universal_Remote_Code_List#Direct_Code_Entry

I have the same clock. Here's what I did to re-set it after changing batteries: After replacing batteries, use the turn dial to set the correct time. Press the RED button 6 times, wait for it to go through that series of chimes, then press the button again to set the time.
Example: Press RED button 6 times. Wait for it to chime. Press RED button the correct number of times for the hour to be set. For 5:00, press the button 5 times, etc.
I lost the directions to my clock, and I am posting this from memory and also just had to re-set mine and it works OK now.
Hope this helps!

All Freeview channels need re-tuned after 30th September.
To re-tune your Sony TV...

1.Press Menu button then go to settings...

2.Scroll down the menu icons until you get to 'Digital Set-up'

3.Press enter/centre key next to direction arrows

4. Select spanner icon and digital audio tuning.

5. You will then be asked if you want to start digital audio tuning.

6. Press enter/centre button....and thats it!.... TV will automatically re-tune.

Generally digital watches all set about the same.
I believe your watch is a Sharp digital alarm/chrono by the number you give.

Hold down the start/stop button in the right corner until the display begins to flash. Once the display flashes you can go through the fields to be set by pressing the mode button.
Some digitals use a different combination but are all about the same.

I would just do it manually or get a universal remote,those come with directions and work for any tv

press the mode button untill you get to the setting where the seconds are flashing.hit the reset button to menuver through the hours, minutes, days, and months.

Note: up = stamp button / down = halftone button

• press function button
  
• press down button until "setmode" is displayed
• press set
• press down until #4 "fax parameters" is displayed
• press set
• press down until #5 "memory" is displayed

Display should be at 2 = ON

• press 1 to change to 1 = OFF
• press red button to close the menu

The memory light should go off when the menu is closed.

To reset the memory state, repeat the steps, but instead, press 2 for 2 = ON and close the menu.

Hope this helps!

You have to hold the component button (TV) and enter the code from http://www.rca.com/codefinder. The SKU it asks for, on my RCR312W, was under the lid from the batteries. Hope it helps.

I just bought one for my wife's aunt and have the book in front of me. Without knowing what codes you need, I would have to list all of them. There are quite a few and it would be very time consuming. There is an alternative.

1. Press and hold the "Code Search" button until the LED stays on.

2. Press the device button (TV, VCR, etc...). The LED will flash once and stay on.

3. Keep pressing the On/Off button until your devise shuts off. then press "Enter".

Hope this helps