Question about Pramac GBW30P Encl Diesel Genset w/Perkins Eng

Open Question

I have genset FG.wilson P200 ,engine perkins common rail,i have problem because the engine low power loss...i

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 251 Answers

SOURCE: low power

Hi ,
firstly i would do a full service on it , all filter and fluids , oil/coolant water,fuel filter(s) and air filters
pay attention to any water seperators , check all fuel line connectors and unions are tight and in good order ( drawing a small amount of air into the fuel system if often the cause of ''a lack of power '')
check your diesel as it absorbs moisture and can severley effect the running of an engine .
if this has no effect
get a rag /goggles and the right size open ended spanner and slacken each fuel injector nut whilst the engine is running , listen for the engine noise going down , if it dosent this means the injector is deffective ( might need replacing or cleaning ) do this to each injector in turn , be very careful as you do this , the diesel is at 200bar pressure and can injected you ( hence the rag )
a final one is the fuel lift pump may be deffective , they often partially work and starve the engine at maximum revs , depending on your engine this will be an electric one or driven directly from the engine block , just follow the fuel lines from your diesel tank ,.
hope this helps


Posted on Jan 17, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i do when some genset can't run togheter when we start the plant


im not sure are you asking about Phasing ? on a three phase gen set , yes extreme care needs be taken if you need to start one genset before shutting one off , in this case a Phase/sync meter will need to be used to keep from surging all the loads connected to genset , also all three phases of each genset needs to be "In sync" to be able to use a transfer from one genset to another , in sync refers to peek waveform on each genset, needs to be in perfect time or an "ARC" will occur , that could be detrimental to the connected loads if there sensative to this type

Jan 18, 2015 | Electrical Supplies

2 Answers

Pramac 25 kva perkins encl diesel genset will not start red light on triangle on check list


Hello. Maybe you have solved your problems. But I still want to share the helpful article to you. https://www.dieselgeneratortech.com/diesel-generators/why-diesel-generator-fail-to-start.html

We are Perkins diesel generator OEM. Can provide 22KW to 2200KW diesel generator set with Perkins engine. https://www.dieselgeneratortech.com/perkins

perkins diesel generators-n5v1fnwbur1qlbncsxenjidv-1-0.jpg

Dec 09, 2013 | Pramac GBW30P Encl Diesel Genset w/Perkins...

2 Answers

I require a service manual for a FG Wilson generator modek P250HE


Can you tell me what control is on that unit. A 2000 or 4001?
Also how old is it? I maybe able to help if I have that

Nov 26, 2013 | Electrical Supplies

2 Answers

I need a parts manual for a perkins new 1000 series


You can download from Perkins engine website, each series engine have detailed instruction manual.

We can provide 22KW to 2200KW Perkins diesel generator with good quality, low fuel consumption, reliable performance, and competitive price. Genset types include open type, silent type, trailer type, portable type and container type genset. We can provide the detailed technical data about the engine.

starlight perkins diesel genset-n5v1fnwbur1qlbncsxenjidv-1-2.jpg https://www.dieselgeneratortech.com/perkins

Apr 18, 2017 | Lincoln Electric Welding Tools

2 Answers

Genset does not start , alarm can't reset


what safety caused the alarm. if you cant restart it, it may be cause the problem that originally shut the engine down has not been fixed, it could be water level, low oil, high water temp, low fuel,over voltage, all of the above are probably run through the safeties. over volt, and water temp would probably clear its self after it sat a while. try turning off power to panel. for a couple minutes and see if it will reset, if not check water level. and oil levels

Aug 12, 2011 | Pramac GBW30P Encl Diesel Genset w/Perkins...

1 Answer

Perkins 3 cylinder powered pramac generator


Start looking at your safety circuits.

1. High water temp
2. Low Oil
3. Low water etc...

From the manual these are the protection circuits.

• Engine protection: low oil pressure, high engine temperature.
• Genset protection: under/over voltage, overload, battery charger failure, battery voltage out of limits,
under/over frequency, start failure.
• Circuit breaker protection: IV poles.
• Differential protection.


Any one of them will trip the fuel relay closed. What you may be able to do is disconnect one at a time each protection circuit and see when the fuel relay opens. (Make sure to reconnect each one if it had no effect on the fuel solenoid)

Once you isolate which circuit it is in then you can chase wires or change the bad switch.

Thanks for choosing FixYa.

Kelly

May 24, 2010 | Pramac GBW30P Encl Diesel Genset w/Perkins...

2 Answers

Its 230kvaperkins generator it starts normally,but after thirty minutes it shuts dawn automatically indicating low frequency


Low frequency means the RPM of the motor has fallen off.

Check your fuel is NOT contaminated or fuel filters plugged.

Further tests should focus on the govenor system. Possibly it fails when engine gets hot. the frequency is directly proportional to the engine speed.

Apr 01, 2010 | Pramac GBW30P Encl Diesel Genset w/Perkins...

2 Answers

Genset can not pick up once main electricity supply is off.


The controller circuit card needs to be replace. This is
the one that senses if and when power is shut off. This
will automatically start the engines.

Nov 03, 2009 | Pramac GBW30P Encl Diesel Genset w/Perkins...

Not finding what you are looking for?
Pramac GBW30P Encl Diesel Genset w/Perkins Eng Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pramac Electrical Supplies Experts

Marvin
Marvin

Level 3 Expert

84966 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

wadingriver
wadingriver

Level 3 Expert

2223 Answers

Are you a Pramac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...