Kenmore Elite washer - control light is on and ii cannot do anything? Please help how do i unlock this feature??

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

April 8 2002 DIV 26 SOURCE 110 KENMORE ELITE HE3 & HET WASHERS "ADD-A-GARMENT" INDICATOR LIGHT ON DOOR WON'T UNLOCK WHEN PAUSE/CANCEL BUTTON IS DEPRESSED.

MODELS: See additional page for Kenmore model numbers

COMPLAINT: Due to a Microcomputer Machine Control software error , the ADD-A-GARMENT feature becomes inoperative.

CORRECTION: The Microcomputer Machine Control must be replaced with a service part that has been reprogrammed to prevent ADD-A-GARMENT feature loss.

PARTS: Order electronic control listed on this service flash by model from Division 26 , Source 110 following normal ordering procedure.

MERCHANDISE CODES: WASHER Service Flash - Model Nurnbers for: Kenmore Elite HE3 & HE3t Washers: "ADD-A-GARMENT" indicator light on door won't unlock when Pause/Cancel button is depressed. Kenmore models with serial Numbers beginning with CSL23 through CSM04 11042822200 11042824200 11042826200 11042832200 11042834200 11042836200 11042922200 11042924200 11042926200 11042932200 11042934200 11042936200 Electronic conrrol p/n 8181900 Electronic control p/n 8181899



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Hi


Thanks for using FixYa. To unlock the controls you’ll need to press and hold the DRAIN/SPIN button for 10-15 seconds. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

April 8 2002 DIV 26 SOURCE 110 KENMORE ELITE HE3 & HET WASHERS "ADD-A-GARMENT" INDICATOR LIGHT ON DOOR WON'T UNLOCK WHEN PAUSE/CANCEL BUTTON IS DEPRESSED.

MODELS: See additional page for Kenmore model numbers

COMPLAINT: Due to a Microcomputer Machine Control software error , the ADD-A-GARMENT feature becomes inoperative.

CORRECTION: The Microcomputer Machine Control must be replaced with a service part that has been reprogrammed to prevent ADD-A-GARMENT feature loss.

PARTS: Order electronic control listed on this service flash by model from Division 26 , Source 110 following normal ordering procedure.

MERCHANDISE CODES: WASHER Service Flash - Model Nurnbers for: Kenmore Elite HE3 & HE3t Washers: "ADD-A-GARMENT" indicator light on door won't unlock when Pause/Cancel button is depressed. Kenmore models with serial Numbers beginning with CSL23 through CSM04 11042822200 11042824200 11042826200 11042832200 11042834200 11042836200 11042922200 11042924200 11042926200 11042932200 11042934200 11042936200 Electronic conrrol p/n 8181900 Electronic control p/n 8181899



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

The following link explains how to correct a Control Lock problem on a Kenmore Elite:

http://www.fixya.com/support/r2469429-kenmore_elite_amp_whirlpool_duet

Some front panel features differ between models, but the instructions should be listed on the front panel of the washer, and are located in the operator/owner's manual. If these preliminary measures do not work, you may have a mnore serious problem.

If you have any questions, please let me know. I hope this helps you.

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Just remember, the instructions are printed near the button. This features locks and unlocks the control panel as a designed safety feature to prevent small children from manipulating the controls. In addition, if you get error codes, or the panel starts flashing or freezes up, sometimes these errors can be erroneous. Unplugging the unit for 30 minutes will reset the Central Control Unit (CCU). This is the main "brain" of the washer. Any error code following a computer reset, is usually a genuine problem. If you ever have questions about this washer in the future, please keep me in mind. Congrats on getting it working again!