Problem with saving time and date

Question 1

0helpful

1answer

Why am I getting the message "the system cannot find the path specified" when trying to scan?

Hi Tania,
You receive this notice when the drive and folder the scanner is configured to save the scan is missing. You can correct this by telling the computer where to save the scan. follow this simple steps.

On your computer desktop, click Start - open Devices and Printers -
Right-click on the printer/ scanner icon and select scan options. Assign a destination folder for saving your new scans.

Please rate me if this helps.

Oct 08, 2014 • Canon PIXMA MX452 Wireless Inkjet...

0helpful

6answers

Photosmart C5180

Hi

1. Double Click on HP director to start it up. Look for "HP Director" on your desktop (the screen in front of you). It is usually an icon that materializes after you install your printer. (It may look slightly different with different models.

2. Scan the document by clicking "Scan."

3. Select "Save to File." (You can set up a folder ahead of time so you know where to find the document or photos once they are scanned). Often times the computer

will create a default "scanned documents" folder and organize them by saving them on the date scanned.

4.Click scan and then wait for box to appear.

5.The software will prompt you to save the file. Put it in the folder you created (you can see the path/folder). Give it a name you will remember.

6.Then click "Save"to finalize it. The document should be in the folder that you designated.

Hope this helps

Aug 07, 2008 • HP Photosmart C5180 InkJet Printer

tip

Canon image CLASS MF5700 Series Scanning

Scanning with [Start] on the Machine
By pressing [SCAN] [Start] on the operation panel of the machine, you can scan
documents to your computer.
Pressing [SCAN] [Start] has the same effect as clicking [Save] in the MF Toolbox.
You can change the settings for [Save], or set up a button other than [Save] to
perform the same operation. (See “Setting the Scanning Function for [Start],” on p.
3-3.)
NOTE
You can use the machine for only a local scanner (connected directly to your computer).
1 Place the document face-down on the platen glass or load it
face-up in the ADF
2 Press [SCAN] [Start] on the machine.
If you are asked to select a program to launch, select “MF Toolbox Ver4.7.”
Scanning starts.
The MF Toolbox and the [Save] dialog box will open, but the document will be
scanned without pressing [Start] in the [Save] dialog box.
The scanned document will be processed according to your settings.
When you use [Start] for the first time, a folder with the scanning date will be created in
the [My Pictures] folder in the [My Documents] folder, and your document will be
saved in this folder. If there is no [My Pictures] folder, the folder with the scanning date
will be created in the [My Documents] folder and your document will be saved in this
folder2 Press [SCAN] [Start] on the machine.
If you are asked to select a program to launch, select “MF Toolbox Ver4.7.”
Scanning starts.
The MF Toolbox and the [Save] dialog box will open, but the document will be
scanned without pressing [Start] in the [Save] dialog box.
The scanned document will be processed according to your settings.
When you use [Start] for the first time, a folder with the scanning date will be created in
the [My Pictures] folder in the [My Documents] folder, and your document will be
saved in this folder. If there is no [My Pictures] folder, the folder with the scanning date
will be created in the [My Documents] folder and your document will be saved in this
folder2 Press [SCAN] [Start] on the machine.
If you are asked to select a program to launch, select “MF Toolbox Ver4.7.”
Scanning starts.
The MF Toolbox and the [Save] dialog box will open, but the document will be
scanned without pressing [Start] in the [Save] dialog box.
The scanned document will be processed according to your settings.
When you use [Start] for the first time, a folder with the scanning date will be created in
the [My Pictures] folder in the [My Documents] folder, and your document will be
saved in this folder. If there is no [My Pictures] folder, the folder with the scanning date
will be created in the [My Documents] folder and your document will be saved in this
folder

on Dec 08, 2009 • Office Equipment & Supplies

0helpful

1answer

How do I set my canon mx 870 to scan

Hi.
This the user manual scanning using canon mx870.
just follow this step by step.
Select the scan operation.

(1) Make sure that the power is turned on.

(2) Press the SCAN button.

If you specified the same computer to save scanned data last time, go to (5).

(3) Use the or button (Scroll Wheel) to select PC , and press the OK button.

The computer selection screen will appear.

Besides saving scanned data on the computer, you can save them on a memory card or USB flash drive, or attach them to E-mail on the computer.

(4) Select the computer to save or forward scanned data, and press the OK button.

(5) Select the document type, and press the OK button.

Hope can help you.regards

Jun 14, 2011 • Office Equipment & Supplies

0helpful

1answer

My monitor won't come out of power save mode. How do I get it out of power save mode?

Problem is not with Dell E197FP LCD Monitor, it happens sometime and the culprit usually is an empty battery on the motherboard. The motherboard battery is used when the mains power is off. When your computer detects an empty battery, it goes into a low-power mode.
The computer will then display as message, like "Power save mode - press any key on keyboard or move mouse".
Better to replace battery:-

open the case of your computer;
visually scan the motherboard for a button-cell battery (it looks like a digital watch battery, but a bit larger);
remove this motherboard battery from your computer;
restart your computer: it should now power up normally (you may get some warning messages but ignore them);
set the date and time of your computer using the "Date and Time" control panel;
you can now use your computer normally, but you will lose date and time settings when you disconnect the computer power cord, since there is no motherboard battery present to store them;
replace the battery or buy new;
install the new battery in your computer;
restart your computer, and set the date and time again; the settings will now be saved using motherboard battery power.

Dec 09, 2010 • Dell E197FP LCD Monitor

0helpful

1answer

My 5305 constantly goes into power save mode

Hi

Thank you for your query

This is a common fault on Dells please try the following

It seems it is a motherboard battery problem. try this.
It most likely is not the monitor which is in "power save mode", it is the computer itself.

When you cannot get a computer out of "power save mode" by any other means, typically the cause is that the button-cell-type battery of your computer, which is located on the motherboard, is empty.

Usually, this happens on a computer which is a few years old, since its batteries will have run out after such a long time. (The motherboard battery is used to store various settings when the computer power is off, such as date and time. When your computer detects this battery is empty, it goes into a low-power mode).

The solution is to replace the button-cell battery on the motherboard of your computer:

- open the case of your computer;
- visually locate the motherboard (the main electronic circuit board) of your computer;
- visually scan the motherboard for a button-cell battery (it looks like a digital watch battery, but a bit larger);
- remove this motherboard battery from your computer;
- restart your computer: it should now power up normally (you may get some warning messages during the start-up sequence, but ignore them);
- set the date and time of your computer using the "Date and Time" control panel;
- you can now use your computer normally, but you will lose date and time

If this has been useful please leave positive feedback/vote/testimonial - Thank you again

Feb 13, 2010 • Dell Inspiron 530s Desktop Computer

1helpful

1answer

My computer's bios doesn't save anything

Here's the manufacturer info link
http://www.intel.com/products/motherboard/DG31PR/configs.htm

BIOS Loses Date and Time (or Changed Settings Not Saved)
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the voltage of the CMOS battery drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. If you find that date and time is incorrect or if you make BIOS setting changes but they are not saved, replace the battery with an equivalent one. Caution Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.
To replace the battery, follow these steps:

Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter).
Remove the computer cover.
Locate the battery on the board.
With a medium flat-bladed screwdriver, gently pry the battery free from its connector. Note the orientation of the “+” and “-” on the battery.
Install the new battery in the connector, orienting the “+” and “-” correctly.
Replace the computer cover.

Jul 10, 2009 • Intel D915GAG Socket 775 Motherboard -...

11helpful

2answers

Dell monitor dialog box says monitor is in the power save mode

Actually, it most likely is not the monitor which is in "power save mode", it is the computer itself.

When you cannot get a computer out of "power save mode" by any other means, typically the cause is that the button-cell-type battery of your computer, which is located on the motherboard, is empty.

Usually, this happens on a computer which is a few years old, since its batteries will have run out after such a long time. (The motherboard battery is used to store various settings when the computer power is off, such as date and time. When your computer detects this battery is empty, it goes into a low-power mode).

The solution is to replace the button-cell battery on the motherboard of your computer:

open the case of your computer;
visually locate the motherboard (the main electronic circuit board) of your computer;
visually scan the motherboard for a button-cell battery (it looks like a digital watch battery, but a bit larger);
remove this motherboard battery from your computer;
restart your computer: it should now power up normally (you may get some warning messages during the start-up sequence, but ignore them);
set the date and time of your computer using the "Date and Time" control panel;
you can now use your computer normally, but you will lose date and time settings when you disconnect the computer power cord, since there is no motherboard battery present to store them;
take the motherboard battery to an electronics store and get a replacement;
install the new battery in your computer;
restart your computer, and set the date and time again; the settings will now be saved using motherboard battery power.

Dec 06, 2008 • Dell Dimension 2400 PC Desktop

0helpful

2answers

SCANER,PRINTER,COPYER

Saving a scanned image on the computer
1 Load an original document facedown on the scanner glass.
2 Close the top cover.
3 From the desktop, double-click the Lexmark Imaging Studio icon.
4 Click Scan.
5 Select the Photo, Several Photos, or Document option.
6 Click Start.
7 From the Save or Edit screen menu bar, click Save.
8 To save to another folder, click Browse, and select a folder. Click OK.
9 To rename the file, enter the name in the File Name area. To assign the name as a prefix to all of your photos,
select the “Start all photos with File Name” check box.
10 To save the photo as another file type, select the file type from the File Type drop-down list.
11 To select a date for the photo, click the drop-down list, and select a date from the calendar.
12 Click Save.

Jan 22, 2008 • Lexmark X2500 All-In-One Printer

0helpful

2answers

My computer went back to older clock date as 1610

try starting your computer in safe mode and see if you can do anything productive there, like scanning for viruses or spyware. also check if you can do the following:
CTRL+ALT+DEL (open task manager)
goto Start>Run>Regedit (open registry editor)
goto Start>Control Panel>Display>Properties (change display settings)
right click on clock at tray and change the current time to correct settings

if you cannot do any of these activities, then your computer may probably been compromised by a virus or malware.

Jan 02, 2008 • Dell OPTIPLEX GX150 PIII-1.0GHz 256MB 40GB...

Question 2

Aneesh Aloor

Contributor 56 Answers
Posted on Jun 01, 2014

Aneesh Aloor

Contributor

Joined: Oct 27, 2009

Answers

56

Questions

0

Helped

31857

Points

87

After the warming up machines wants the Date and time.
first you press the stop button then enter 0101 followed by "enter" button. after one mints you machines display shows
"ready 100%"

if you are switch off the machines more than 7 hrs. again ask the date and time , then do the same steps above.

if you wants to enter the correct date and time pls. enter the month as first , then date , then year. suppose you want to enter today's date
like " 06012014"
ok....

Dan Pura Jan 24, 2017

Thank you very much! Thank you very much!

×

Answer 2

Anonymous

Contributor 2 Answers
Posted on May 23, 2008

Anonymous

Contributor

Joined: May 23, 2008

Answers

2

Questions

2

Helped

1188

Points

3

Hi problem is cru fuse error on display what do i my problem tecnical

Related Topics:

Problem with saving time and date

2 Answers

Aneesh Aloor

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Why am I getting the message "the system cannot find the path specified" when trying to scan?

Photosmart C5180

Canon image CLASS MF5700 Series Scanning

How do I set my canon mx 870 to scan

My monitor won't come out of power save mode. How do I get it out of power save mode?

My 5305 constantly goes into power save mode

My computer's bios doesn't save anything

Dell monitor dialog box says monitor is in the power save mode

SCANER,PRINTER,COPYER

My computer went back to older clock date as 1610

Not finding what you are looking for?

SCX 4521F All-In-One Laser Printer

Why am I getting the message "the system cannot find the path specified" when trying to scan?

Ask a Question

Check Out the Latest Printers Report

Top Samsung Office Equipment & Supplies Experts

Cindy Wells

Grand Canyon Tech

Norman Weimar

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Problem with saving time and date

2 Answers

Aneesh Aloor

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Why am I getting the message "the system cannot find the path specified" when trying to scan?

Photosmart C5180

Canon image CLASS MF5700 Series Scanning

How do I set my canon mx 870 to scan

My monitor won't come out of power save mode. How do I get it out of power save mode?

My 5305 constantly goes into power save mode

My computer's bios doesn't save anything

Dell monitor dialog box says monitor is in the power save mode

SCANER,PRINTER,COPYER

My computer went back to older clock date as 1610

Not finding what you are looking for?

SCX 4521F All-In-One Laser Printer

Why am I getting the message "the system cannot find the path specified" when trying to scan?

Related Topics

Ask a Question

Popular Questions

Samsung SCX-4521 "Paper Jam 2" won't clear

When i print ,I get

How do I scan with the samsung scx-4200?

Samsung scx-4521f fax memory received but never print out.

How to reset toner ,Samsung SCX-4623F

Check Out the Latest Printers Report

Top Samsung Office Equipment & Supplies Experts

Cindy Wells

Grand Canyon Tech

Norman Weimar

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Manuals & User Guides