Need cable for xtronix joy stick to plug into xtronix base of chair this cable has two large pins with two small pins each side of large side while driving chair caught cable and pulled it out from bottom xtronix . this control is for Quickie S 525 series I know this is old Quickie however really need chair for driving VAN I made mistake getting a jazzy with 14 inch wheel legs press against sterring wheel

From the mid 2000s until the 2013 model, you can pull the headrest on your Chevrolet Silverado 1500 up to the full-up position by pressing the button at the base of the inboard leg of the headrest. You then stick a small-diameter tool -- the leg of a heavy paper clip or a small pin punch -- into the hole on the base of the inboard side of the outboard headrest leg. Pull up with the pin inserted and the headrest comes off. On the 2014 Silverado 1500, press the large and the small buttons on the base to pull off the headrest instead of using a pin punch

Hand control is locked. turn chair on push joy stick forward til it beeps then pull it back until it beeps then put it in neutral ( joy stick in the center) then it should be unlocked.
LOCKING/UNLOCKING THE VSI
The VSI has a feature that enables you to lock your power chair to prevent
unauthorized use.
To lock the VSI:
1. With the VSI powered on, press and hold the on/off key. After one (1)
second, the VSI should beep.
2. Release the on/off key.
3. Push the joystick to the full forward position until the VSI beeps.
4. Pull the joystick to the full rearward position until the VSI beeps.
5. Release the joystick. There should be a long beep.
6. The VSI is now locked.
To unlock the VSI:
1. Press the on/off key and power on the VSI. The maximum speed/profile
indicator should ripple side to side.

There is one large cable that leads down to the bottom of the engine(starter). This goes on one of the large terminals on the solenoid. All the rest of the wires with large eyelets go on the other side which includes the cable from the battery. The small push on terminal goes on the small stud. If you have two small studs, it should go on the one closer to the front of the truck.

The lights indicate you are in charge mode or inhibit. Check to make sure the charger isn't plugged in. If it isn't then the inhibit function of the chair is bad and will have to be repaired Hope this helped

Flo First you have to unplug the nine pin connector at the rear of the chair and the 3 pin charger plug. Then there is a handle under the right side of the seat. Push it forward to release the pressure on the seat post. Now the hard part have someone with some strength twist and pull up on the seat at the same time until it comes off the seat post. After the seat is off then remove the plastic shroud covering the base and there you will find the batteries. Unplug the battery cables from the wiring harness and lift out them of the base. Hope this helps you

The jazzy probably has a VSI controller and if it is sleep mode then the lights will scroll rather than blink. Now turn on the chair and see if the blinks have a pause between them, ie 4 blinks pause 4 blinks pause etc If they do count the number of blinks and this will give you the error code ie 4 blinks right motor 3 blinks left motor your owners manual should have a chart listing the error codes If not you can contact Pride tech support @ 1-800-800-8586 ask for jazzy tech support

Hope this helps

LOCKING/UNLOCKING THE VSI

The VSI has a feature that enables you to lock your power chair to prevent

unauthorized use.

To lock the VSI:

1. With the VSI powered on, press and hold the on/off key. After one (1)

second, the VSI should beep.

2. Release the on/off key.

3. Push the joystick to the full forward position until the VSI beeps.

4. Pull the joystick to the full rearward position until the VSI beeps.

5. Release the joystick. There should be a long beep.

6. The VSI is now locked.

To unlock the VSI:

1. Press the on/off key and power on the VSI. The maximum speed/profile
indicator should ripple side to side.

Good Luck
mimobility

Under your Control Panel with Joy Stick there is in Small round port hole , and this is where you Charge your Chair, You will when you look under the front of this panel the hole with (3) Pins Connect here, and good Luck,

Gerry.

call 866-722-4581 for lowest prices: your M41 joystick is part# 1147600 and cost: $999.00

The flashing will come on if the chair is in neutral or if the charger is still plugged in when you turn it on. Place the chair in neutral (freewheel) by shifting the levers out, then place firmly back into drive.

Unplug from the charger and it should fire up. Sometimes, the chair will also go into "sleep mode".
Check your owners manual for this. Note, some have sleep mode potential but it's not in the manual, and if someone inadvertantly hits the right series of motions with the joystick, you can inadvertantly put it to sleep. Try turning the chair off, wait three seconds and power back up, then immediately press the "horn" button. This wakes up most of them. Others you need to power off, turn back on and then move the joystick forward, backward then forward again.

Good luck