DI3510f Well my problem is that when the paper comes out of the LCC, large capacity cassette, it comes out crooked and sometimes it jams. The image doesn't come out out of place but the paper does Any suggestions that you can give me will be helpful Thanks

check the right door the sponge looking roller and area around it for a problem that section is call registration aligning the paper up before the image goes on it the sponge roller actually trans fer the image on to the paper so the problem is before it check the mylar clear plastic before the the transfer roller section should be on the assembly or below it also check the paper dust remover it clips in on the assy.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

LSU - Print Head which houses the (LASER)

LCC - Large Capacity Cabinet (Holds a Lot of Paper, more than a normal tray)

SRAM - Static Random-Access Memory

CPT - Toner Cartridge Code

PTC - Primary Transfer Belt Cleaning Unit

MFP - Multi- Function Printer Control Board

SCU - Scanner Unit

PWB - Printed Wire Board (Circuit Board)

Hope that helps

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

This refers to the LCC (large capacity cassette) is not lifting the paper. Sometimes the paper can foul when incorrectly loaded & the copier cannot recognise the paper present in the cassette. To reset the error use SIM 15.

Some tray are hard set certain types of media (paper) other have moveable guides C350 has moveable guides for the first draw and second LCC (large capacity) as set for one size

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hi this is what i found for your problem hope it helps thanks. Paper feed cam sensor error or Error Code 6B10
Condition: An error occurred in the paper feed cam sensor during paper feeding from the cassette, or the paper absorbing a large amount of ink jammed in the PF rear guide.
Problems and Solutions:

• Jammed paper in the PF rear guide (when a large amount of ink was absorbed in the paper);
  - remove the jammed paper and foreign material.
• check for foreign material or paper debris in the cassette or in the PF rear guide;
  - remove foreign material.
• If other solution fail, replace one off the following part
  - PF pick-up unit
  - Logic board

Try cleaning the paper feed rollers for that cassette. Sometimes the rollers get dirty causing the paper to slip and not feed from the cassette causing the machine to register a paper jam.

The rollers can be cleaned with rubbing alcohol and a cloth.

When the printer "Ready" and "Alarm" LEDs flash as shown, please check the following points:
1.Paper Jam: Clear the paper jam referring to "How do I clear paper jams?"
If the printer does not automatically resume printing, press the control panel button.
2.No Paper/ Misfeed:
-The paper cassette may be out of paper or not properly installed.
-If it is empty, load a new stack of paper into the paper cassette.
-If there is paper in the paper cassette, make sure it is straight.
-If the paper is curled, straighten it before printing. Sometimes it is helpful to remove the paper, turn the stack over and put it back in the paper cassette.
-Reduce the amount of paper in the paper cassette, and then try again.
-Make sure you use paper that meets Brother's recommended paper specifications.
-Reinstall the paper properly, and then press the control panel button. The printer will start printing again.

Hi ..

This error comes when the paper is not loaded properly in the cassette ... Follow the below instructions to load the cassette and I am sure you will not get the error again.

1. Grip the cassette handle, and pull it out towards you until the cassette comes to a stop.
   
   
   
   
2. Open a package of paper, and remove the paper stack. If the paper is curled, uncurl it before placing it in the cassette. Failure to do so will cause paper creases and a paper jam. 17 lb to 20 lb bond (64 to 80 g/m2 ) paper is acceptable. The cassette holds up to approximately 500 sheets of 20 lb bond (80 g/m2 ) paper.
   
   
3. Load the paper stack beneath the cassette's length guide (1) and width guide's claw (2).
   Make sure that the paper stack does not exceed the length and width guides' claws in the cassette. Failure to do so will cause a paper jam. Do not load extra paper when there is still paper left in the cassette. Only load one size of paper into the cassette. Do not load different sizes of paper into the cassette at the same time. Do not load labels or transparencies into the cassette.
   
   
4. Gently insert the cassette as far as it will go.

The cassette is for plain paper, colored paper or recycled paper only. Loading other paper in the cassette may cause a paper jam. If copies are curled, or a paper jam occurs, remove the paper stack from the cassette. Turn it over and then place it in the cassette. If you load paper while making copies, do not load a different paper size.
Closing the cassette When closing the cassette, make sure to push it in completely as far as it will go. If copying is performed when the cassette is not pushed in completely, it will cause a paper jam.

If copy paper is sticking out of the cassette Sometimes, when you pull out the cassette, paper may stick out, as shown in the illustration below. Make sure that the paper is neatly loaded into the cassette, before you push the cassette back into the main unit.

Don't forget to vote if this helps ... Cheers :)

The error E2-06 indicates a problem with paper tray lift in the Large Capacity Cassette (LCC) It could be a faulty lift motor or bad sensor. In this particular case someone crammed way too much paper into the lift tray. I took out half of the paper, restarted the machine and the error cleared.

check that the paper guides on paper cassette are hard up against paper edges