Mitsubishi 65819 problem with the green light code is 2 green blinks a pause and then 1 green light

ost models have a self-diagnosis feature to help determine shutdown problems.

To enable this feature do the following....

1) Turn the tv on and then let it shutdown
2) Press the input and menu buttons on the front panel simultaneously and hold them in for 5 seconds
3) After 5 seconds the power LED on the front panel will blink a two digit sequence.

This will commonly be one set of blinks followed by a short pause then another set of blinks.
This will repeat around five times.

1 - 2 = no error detected

2 - 1 = X-ray protect (high voltage or beam current)

2 - 2 = Short protect (short detected - commonly caused by convergence failure - to repair this check out site for a convergence kit)

2 - 3 = Deflection protect

2 - 4 = Vertical protect


Note: A constant blink on certain models will typically be caused by a fault in the DM model. To repair this check out site a "blinking green light kit"

If the green power light comes on for a few seconds at turn on and goes out do the self check this set has(I will be here on and off for a while):

when light goes out on the front of the set press and hold BOTH the menu and input (input can be labeled source on some models) for at least five seconds and release both buttons.

Power light will blink a two digit error code like 2 blinks, 2 blinks, a pause and repeat it for a total of 5 times.

Let me know what error code if any is found and I will direct you.

Note that if you have removed power from the set that will clear the error code and give you a 1,2 error which of course is no error--you have to plug set up and try again to turn it on and do the self check when it fails.

SD TECH

shutdown is happening= If set has been unplugged plug it back in and turn set on--when green power light goes off in a few seconds:

On front of set (not the remote) press and hold both the Menu and Input (Device) buttons at same time and hold for at least 5 seconds---then release both.

Power light will blink an error code like 2 blinks, 2 blinks pause and repeat it for a total of 5 times.

Let me know what error code is and I will tell you what it means.

SD TECH

Hi Sharon,

Blinking of the LED at the front panel has an equivalent error code to give an idea what's going wrong to the set. Please check if there's a pattern of blinks, number of blinks separated with a pause or if the led blinks green continuously.

Jdvillanueva

To determine what your problem is:

UNPLUG TV ANDTHEN PLUG BACK IN---TURNON---GREEN POWER LIGHT COMES ON FOR A MOMENT ANDGOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.

Let me know



SDTECH

The TV indicates an error code 22 (short circuit protection). Check 2 STK392-570 convergence IC for shorts and 5amps pico fuse for open. I usually replace both STK's.

Ur power board ic converter it dead.
Ur Convergence board is bad going to die to.
Both must change.

The DM is fine if the led isnt blinking. Your set is going into protective shutdown. Try pressing the menu and the device/input buttons on the set both in together for 5 seconds to see if the set will blink a series of blinks pause then blink another series of blinks. Such as 2 blinks pause then 2 blinks, Then let me know what the blinks were and I will assist you with whats wrong

turn off sleep mole

Self test: Turn on and Press the input and menu buttons on front panel together and hold for 5 sec. after 5 sec the power LED will blink a 2 digit seq. This will let you know what error code. Count the first blinks then a short pause then the second blinks. Example 2-3, 3-4, 4-1. Let us know what it is