Mad Catz PS3 Bluetooth® Headset Wireless Headset Logo
Posted on Aug 26, 2010

I just bought my madcatz headset from the shop. Charged it for 4 hours and the red LED turned off so I suppose it is charged. Then i go to the “Manage Bluetooth® Devices.” and go to the screen where it says start scanning. I hold the power button until it starts flashing red and blue. Then I press X to start the scan. The problem is that the screen says only Scanning... Please wait.( I have tried multiple ways like holding the power button down all the time or just clicking it or what ever) On the box it says compatible with/avec PS3 playstation.3 so it shud work? Help please.

  • Anonymous Aug 27, 2010

    Do you have the headset attached to the USB cable when trying to pair up

×

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 6 Answers
  • Posted on Aug 29, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Aug 29, 2010
Answers
6
Questions
0
Helped
3823
Points
16

The power button is not the right button to press.

Here is the steps I take:

1. Power on the headset
2. Have PS3 scan for new devices
3. Hit the tiny button that is next to the volume buttons on the top of the headset.
4. PS3 should recognize "8860" and ask for a passkey which is "0000" by default
5. Paired and ready to go

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My nokia bh503 headset not charging

Leave it plugged in for 4 hours. Yello should turn red then green when fully charged
3helpful
2answers

My brand new madcatz bluetooth headset wont charge, when plugged in the charging light is red, but it increases/ decreases in brightness after 4 hours it will not turn on or sync. This is the second one...

i just got mine and it when i plug it in to charge the red light turns on for like 10 seconds then turns off and it wont turn on so itss dead... return it?
0helpful
1answer

I'm charging the headset and the led is blinking red, but when i disconnect the usb, i still can't turn it on

When the headset's battery is fully charged (about 3 hours), the indicator light is steadily lit in blue
1helpful
1answer

Mine wont turn on

Hello, did you check the battery? Tu get the full charge, the headset red light must stay steady on. If you get it charged you can pair it: hold power button till the two leds blinks, now scan for bluetooth from PS3 and choose your mic setting. Other than that I'd call madcatz technical support. Good luck, Peter_Rei
0helpful
2answers

The red light indicator says it's charging, but it isn't.

idk that happen to me too buht my blue toooth i just baught a gamestop madcatz .. and on the instruckstions sheeet it says if its charging it;ll turn red . buht myne turn red for like 3 sec then it disapeares .... :O
0helpful
1answer

MadCatz8860 Won't Charge

when you buy it for the 1st time, charge it up for double the reckemended 1st charge
1helpful
1answer

Charging H550

The indicator light turns red when the battery is
charging. It may take up to 1 minute for the
indicator light to turn on. When the headset's
battery is fully charged (about 2 hours), the
indicator light turns off.
1helpful
1answer

Charging

There's a small power jack under a tab at the base of the unit. I found it only charges if you plug it into the transformer travel charger. For some reason plugging it in the PC USB port doesnt work.

If the unit is being charged a red LED will light up, turns blue after 2/3 hours when its fully powered up.
6helpful
1answer

Won't charge up...

I had the same issue. So what I did was get a small screwdriver, opened the A210 case removed the battery. You will notice orange tape (remove it) then attached to the battery is a small board (the defective part) . Cut away the board, then you will need to solder the wires back to the thin metal film leads. And voila it will now charge, make sure to never let it charge for more than 2 hours. Do this at your own risk. Of course this will void the warranty.
0helpful
3answers

My motorola H700 keeps staying red when charging

Wait, how long have you waited for it to charge? It's supposed to stay red until over 80% charge, then switch to yellow. When it is fully charged, it goes to green. When you mean it stays red when plugged in, have you waited the 2 hours?
Not finding what you are looking for?

273 views

Ask a Question

Usually answered in minutes!

Top Mad Catz Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1672 Answers

 Grubhead
Grubhead

Level 3 Expert

5755 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Mad Catz Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...